Makita XPP01, Instruction Manual

7 ENGLISH

10. 

Remove and check the carbon brushes reg-

ularly. Replace them after 200 times of use.

Carbon brushes with a length of about 6 mm 

(15/64″) or less may cause damage to the motor.

11. 

When using the tool continuously, its tempera-

ture can exceed 70 °C which may cause lower 

performance. In this case, stop operating for 

about 1 hour to allow the tool to cool down 

before using it again.

12. 

Do not cover or clog the motor air vents as this 

may cause the motor to overheat, resulting in 

smoke, fire and explosion.

Symbols

The followings show the symbols used for tool.

volts

direct current

diameter

Important safety instructions for 

battery cartridge

1. 

Before using battery cartridge, read all instruc-

tions and cautionary markings on (1) battery 

charger, (2) battery, and (3) product using 

battery.

2. 

Do not disassemble battery cartridge.

3. 

If operating time has become excessively 

shorter, stop operating immediately. It may 

result in a risk of overheating, possible burns 

and even an explosion.

4. 

If electrolyte gets into your eyes, rinse them 

out with clear water and seek medical atten-

tion right away. It may result in loss of your 

eyesight.

5. 

Do not short the battery cartridge:

(1) 

Do not touch the terminals with any con-

ductive material.

(2) 

Avoid storing battery cartridge in a con-

tainer with other metal objects such as 

nails, coins, etc.

(3) 

Do not expose battery cartridge to water 

or rain.

A battery short can cause a large current 

flow, overheating, possible burns and even a 

breakdown.

6. 

Do not store the tool and battery cartridge in 

locations where the temperature may reach or 

exceed 50 °C (122 °F).

7. 

Do not incinerate the battery cartridge even if 

it is severely damaged or is completely worn 

out. The battery cartridge can explode in a fire.

8. 

Be careful not to drop or strike battery.

9. 

Do not use a damaged battery.

10. 

The contained lithium-ion batteries are subject 

to the Dangerous Goods Legislation require-

ments. 

For commercial transports e.g. by third parties, 

forwarding agents, special requirement on pack

-

aging and labeling must be observed. 

For preparation of the item being shipped, consult-

ing an expert for hazardous material is required. 

Please also observe possibly more detailed 

national regulations. 

Tape or mask off open contacts and pack up the 

battery in such a manner that it cannot move 

around in the packaging.

11. 

When disposing the battery cartridge, remove 

it from the tool and dispose of it in a safe 

place. Follow your local regulations relating to 

disposal of battery.

12. 

Use the batteries only with the products 

specified by Makita.

 Installing the batteries to 

non-compliant products may result in a fire, exces

-

sive heat, explosion, or leak of electrolyte.

13. 

If the tool is not used for a long period of time, 

the battery must be removed from the tool.

SAVE THESE INSTRUCTIONS.

CAUTION:

Only use genuine Makita batteries.

Use of non-genuine Makita batteries, or batteries that 

have been altered, may result in the battery bursting 

causing fires, personal injury and damage. It will 

also void the Makita warranty for the Makita tool and 

charger.

Tips for maintaining maximum 

battery life

1. 

Charge the battery cartridge before completely 

discharged. Always stop tool operation and 

charge the battery cartridge when you notice 

less tool power.

2. 

Never recharge a fully charged battery car-

tridge. Overcharging shortens the battery 

service life.

3. 

Charge the battery cartridge with room tem-

perature at 10 °C - 40 °C (50 °F - 104 °F). Let 

a hot battery cartridge cool down before 

charging it.

4. 

Charge the battery cartridge if you do not use 

it for a long period (more than six months).