background image

9 ENGLISH

Nylon cutting head

Optional accessory

NOTICE:

 The bump feed will not operate properly if 

the head is not rotating.

1

►  

1.

 Most effective cutting area

The nylon cutting head is a dual string trimmer head 

provided with a bump & feed mechanism.

To feed out the nylon cord, tap the cutting head against 

the ground while rotating.

NOTE:

 If the nylon cord does not feed out while 

tapping the head, rewind/replace the nylon cord 

by following the procedures described under 

“Maintenance”.

Adjusting the shaft length

WARNING:

 

Before adjusting the shaft length, 

release the switch trigger and remove the battery 

cartridge from the tool.

 Failure to release the trig-

ger and removing the battery cartridge may cause a 

personal injury.

CAUTION:

 

Make sure to tighten the lock 

sleeve before operation.

 Otherwise the tool may 

lose control and result in personal injury.

To adjust the length of the shaft, turn the lock sleeve 

counterclockwise until the arrow mark on the lock 

sleeve indicates the unlock mark on the housing, and 

pull out or push in the shaft to the desired length.

After adjustment, tighten the lock sleeve until the arrow mark 

on the lock sleeve indicates the lock mark on the housing.

1

2

►  

1.

 Shaft 

2.

 Lock sleeve

ASSEMBLY

WARNING:

 

Always be sure that the tool is 

switched off and battery cartridge is removed 

before carrying out any work on the tool.

 Failure to 

switch off and remove the battery cartridge may result 

in serious personal injury from accidental start-up.

WARNING:

 

Never start the tool unless it is 

completely assembled.

 Operation of the tool in a 

partially assembled state may result in serious per-

sonal injury from accidental start-up.

Installing the handle

Fit the handle onto the shaft and secure it with the bolt 

and the knob.

1

2

3

4

5

►  

1.

 Handle 

2.

 Bolt 

3.

 Knob 

4.

 Cutting tool side

5.

Battery cartridge side

Make sure that the handle is located in the straight area 

of the shaft as shown in the figure.

Installing the protector

WARNING:

 

Never use the tool without the 

protector illustrated in place.

 Failure to do so can 

cause serious personal injury.

CAUTION:

 

Take care not to injure yourself on 

the cutter for cutting the nylon cord.

Summary of Contents for XRU13Z















Reviews: