5 ENGLISH
16.
If the workpiece or blade becomes jammed,
turn the mitre saw off. Wait for all moving
parts to stop and disconnect the plug from
the power source and/or remove the battery
pack. Then work to free the jammed material.
Continued sawing with a jammed workpiece could
cause loss of control or damage to the mitre saw.
17.
After finishing the cut, release the switch, hold
the saw head down and wait for the blade to stop
before removing the cut-off piece.
Reaching with
your hand near the coasting blade is dangerous.
18.
Hold the handle firmly when making an incom
-
plete cut or when releasing the switch before
the saw head is completely in the down posi-
tion.
The braking action of the saw may cause
the saw head to be suddenly pulled downward,
causing a risk of injury.
19.
Only use the saw blade with the diameter that
is marked on the tool or specified in the man
-
ual.
Use of an incorrectly sized blade may affect
the proper guarding of the blade or guard opera-
tion which could result in serious personal injury.
20.
Only use the saw blades that are marked with
a speed equal or higher than the speed marked
on the tool.
21.
Always select the correct saw blade for the
material to be cut. Do not use the saw blade to
cut materials other than those specified.
22.
Do not use the saw to cut other than wood,
aluminum or similar materials.
Additional instructions
1.
Make workshop kid proof with padlocks.
2.
Never stand on the tool.
Serious injury could
occur if the tool is tipped or if the cutting tool is
unintentionally contacted.
3.
Never leave the tool running unattended. Turn
the power off. Do not leave tool until it comes
to a complete stop.
4.
Do not operate saw without guards in place.
Check blade guard for proper closing before
each use. Do not operate saw if blade guard
does not move freely and close instantly.
Never clamp or tie the blade guard into the
open position.
5.
Keep hands out of path of saw blade. Avoid
contact with any coasting blade. It can still
cause severe injury.
6.
Always secure all moving portions before
carrying the tool.
7.
Stopper pin which locks the cutter head down
is for carrying and storage purposes only and
not for any cutting operations.
8.
Check the blade carefully for cracks or dam-
age before operation. Replace cracked or dam-
aged blade immediately. Gum and wood pitch
hardened on blades slows saw and increases
potential for kickback. Keep blade clean by
first removing it from tool, then cleaning it with
gum and pitch remover, hot water or kerosene.
Never use gasoline to clean blade.
9.
Use only flanges specified for this tool.
10.
Be careful not to damage the arbor, flanges (espe
-
cially the installing surface) or bolt. Damage to
these parts could result in blade breakage.
11.
Make sure that the turn base is properly
secured so it will not move during operation.
Use the holes in the base to fasten the saw to a
stable work platform or bench. NEVER use tool
where operator positioning would be awkward.
12.
Make sure the shaft lock is released before the
switch is turned on.
13.
Be sure that the blade does not contact the
turn base in the lowest position.
14.
Hold the handle firmly. Be aware that the saw
moves up or down slightly during start-up and
stopping.
15.
Make sure the blade is not contacting the
workpiece before the switch is turned on.
16.
Before using the tool on an actual workpiece,
let it run for a while. Watch for vibration or
wobbling that could indicate poor installation
or a poorly balanced blade.
17.
Stop operation immediately if you notice any-
thing abnormal.
18.
Do not attempt to lock the trigger in the "ON"
position.
19.
Always use accessories recommended in this
manual. Use of improper accessories such as
abrasive wheels may cause an injury.
20.
Some material contains chemicals which may
be toxic. Take caution to prevent dust inhala-
tion and skin contact. Follow material supplier
safety data.
Additional safety rules for the laser
1.
LASER RADIATION DO NOT STARE INTO
BEAM.
2.
AVOID EXPOSURE - LASER RADIATION IS
EMITTED FROM APERTURE.
3.
USE OF CONTROLS OR ADJUSTMENTS
OR PERFORMANCE OF PROCEDURES
OTHER THAN THOSE SPECIFIED HEREIN
MAY RESULT IN HAZARDOUS RADIATION
EXPOSURE.
Complies with 21CFR
1040.10 and 1040.11
AVOID EXPOSURE-Laser
radiation is emitted from
LASER RADIATION
this aperture
DO NOT STARE INTO BEAM
Maximum Output
<1mW,Wavelength:655nm
CLASS II LASER PRODUCT
CAUTION
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity
with product (gained from repeated use) replace
strict adherence to safety rules for the subject
product. MISUSE or failure to follow the safety
rules stated in this instruction manual may cause
serious personal injury.
