background image

I N T R O D U C T I O N

Malaguti

 reserves the right to make any and all changes to its vehicles as it deems fit and appropriate at any time without prior notice.

No part of this publication

, whether text or illustrations, 

may be reproduced

 or circulated either totally or partially. 

Malaguti

 reserves all rights over this publication. 

Reasons must be given for any request for permission (written) thereto.

FIRST EDITION:  06/08

 

INTRODUCTION

This publication describes all necessary steps for

 troubleshooting concerning the electrical system

 (

Electronic Injection

 System) and of the possible service operations, 

which are necessary for their solution. It supplies the 

trade technicians

 (Authorised Service Centres) with the necessary information for operating in compliance with the 

modern concepts of “good practice” and “safety at work”.

Further information can be derived from the 

“Chassis” workshop manual

, from the 

“Engine” workshop manual

 and from the 

Spare Parts catalogue

.

All described operations must be performed by technicians with the necessary skill and experience.

The steps for the removal of body parts and of electric and mechanical components, to allow access to wiring or electric components to service, can be taken from the 

“Chassis” Workshop Manual.

We recommend you follow the information given in this publication with care.

For any further information you may need, refer to the 

Malaguti S.p.A. 

Technical Department.

It is essential to follow the instructions with great care. Work carried out carelessly or, worse still, work that has not been accomplished, can cause injuries and damage or, 

in the less serious cases, tiresome complaints.

MANUAL UPDATES

Any subsequent 

updates 

applying to this Manual will be sent in a reasonable time.

The table of contents

 will be duly updated in the event that new pages are inserted, which render the consultation of the manual difficult.

  The Electrical System Troubleshooting Manual is to be considered as an essential tool to be properly kept up-to-date so as to maintain its “validity” 

over time.

Summary of Contents for F10 2008









































Reviews: