background image

MALONE

R

Limited Five Year Warranty

MALONE AUTO RACKS, 81 County Road, Westbrook, Maine 04092

Phone:  207-774-9100   Fax:  207-615-0551

Website:  www.maloneautoracks.com   Email:  sales@maloneautoracks.com

Repair or replacement of a defective product, or the issue of a  refund or  credit (as determined by Malone) is the original 

retail purchaser’s exclusive remedy under this warranty.  Damage to original purchaser’s vehicle, cargo, or property, and/

or to any other person or property is not covered by this warranty.

This  warranty is  expressly  made in lieu of any and all other warranties,  express or  implied,  including the  warranties of

merchantability and fitness for a particular purpose.

Malone’s  sole  liability is limited to the remedy set forth above.  In no event will  Malone be  liable for any direct, indirect,

consequential, incidental,  special, exemplary, or  punitive  damages , or,  for  any  other  damages of  any  kind  or  nature

(including but not limited to, lost profits, lost income or lost sales).

Some  states  do  not  allow  the  exclusion  or limitation of incidental or consequential damages, so the above limitations

may  not  be  applicable.  This warranty gives you specific legal rights and you may also have other rights which vary from

state to state.

In  addition,  all  vehicular  transports  are  potentially  hazardous.  Any  person  using  MALONE  products  are   personally

responsible  for  following the given directions for use, installation and accepts full responsibility for any and all damages

or injury of any kind including death, which may result from their use.

The Malone Auto Racks (Malone) Limited Five Year Warranty covers certain Malone-brand products that have been specifically

identified for inclusion in the  program and is effective  for five years from the date of purchase for the original  retail  purchaser.

This warranty is terminated after five  years  from the date of purchase, or, when the  original retail  purchaser sells or otherwise

transfers the product to any other person or entity during the five year warranty period.

Subject  to  the  limitations and  exclusions  described  in  this  warranty,  Malone will remedy  defects in materials and/or

workmanship by repairing or replacing, at its option, a  defective  product without charge for parts or labor.  Malone may

elect, at its option, not to repair or replace a defective  product  but  rather issue to the  original  retail purchaser a refund

equal  to the  purchase  price  paid for the  product, or credit to be  used  toward the  purchase of a  replacement  Malone

product. 

This  warranty does not cover, and no warranty is given for defects or problems  caused by normal  wear  and  tear  which

includes  but  is  not  limited  to  surface  (aesthetic)  metal  corrosion,  scratches,  dents,  deformities,  accidents,  unlawful

vehicle operation, or any modification of a product not performed or authorized in writing by Malone.

In addition, this warranty does not cover problems resulting from conditions beyond  Malone’s control including, but not

limited to,  theft,  misuse,  overloading, or failure to assemble, mount  or  use  the  product  in  accordance  with  Malone’s 

written instructions or guidelines included with the product available to the original retail purchaser.

No warranty is given for Malone products purchased outside of the United States, Canada and Mexico.

If the product is believed to be defective, the  original  retail  purchaser  should  contact the  Malone dealer from whom it

was purchased, who will give the original retail  purchaser instructions on how to proceed.  If the original retail purchaser

is unable to contact the Malone dealer, or the dealer is not able to remedy the defect, the original retail purchaser should

contact Malone by email at 

technical@maloneautoracks.com.

In  the  event  that the  product must be  returned to  Malone, a  technician at  the  email  address  above will  provide the

original purchaser with return  shipping instructions.  The  original  purchaser  will  be  responsible for the cost of  mailing

the  product  to  Malone.  In  order to  receive any  remedy under this  warranty,  a copy of  the  original  purchase  receipt, 

a description of the defect and a return address must be provided. 

Disclaimer of Liability

Summary of Contents for MPG460XT






































Reviews: