background image

OWNER’S MANUAL

iv

iii

PRODUCT

RATINGS

MOTOR RATINGS

POWER RATINGS

FCC COMPLIANCE

 

 The•Structures™•S755•Adjustable•Base•motors•are•not•designed•to•operate•for•more•than•two•

[2]•continuous•minutes•within•an•eighteen•[18]•minute•time•period.•Exceeding•this•rating•will•shorten•

the•life•of•the•motors,•and•will•void•the•warranty.

 

 This•product•is•designed•to•have•no•maintenance•requirements•by•the•user.•Please•do•not•open•

any•motor•compartments,•alter•the•wiring,•modify•the•base,•or•change•the•product•in•any•way•as•

it•will•void•the•warranty.•••

 

  

INPUT:

 

AC 100-240V - 50/60Hz, 1.5 Amp

 

  

OUTPUT:

 

DC 29V-2A

 

 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device 

may not cause harmful interference, and (2) this device must accept any interference received, including interference 

that may cause undesired operation. 

••Operates•on•2.4•GHz•frequency•transmitter.

 

 To comply with the FCC RF exposure requirements, no change to the antenna or the device is permitted. Any change 

to the antenna or the device could result in the device exceeding the RF exposure requirement and void user’s right 

to operate the device.

For•any•questions•or•concerns•regarding•this•product•please•contact•

malouf

®

•directly:

IMPORTANT: USE THIS PRODUCT ONLY AS DESCRIBED IN THESE 

INSTRUCTIONS. DO NOT MODIFY ANY PARTS OR COMPONENTS.

Summary of Contents for Structures S755























Reviews: