background image

– 16 –

ALL OUR PRODUCTS ARE MADE FROM THE FINEST QUALITY MATERIALS

AND ARE MANUFACTURED UNDER THE STRICTEST QUALITY CONTROLS

We guarantee all our products or part thereof, for a period of six months from the date of delivery to the consumer

against faulty manufacture. This guarantee is not effective against damage caused as a result

of incorrect usage of the product or accidental damage. This in no way affects your statutory rights.

INSTRUCTIONS FOR SAFE USE & MAINTENANCE

The maximum height (i.e. upper surface) of any mattress fitted must not exceed the line engraved on the
inside of the cot ends. We recommend the use of the Mamas & Papas size: 400 mattress. 

Due to constant updating and improvements, some components may occasionally differ slightly from the diagrams shown in these instructions.
Any spare components should only be thrown away after you have 

fully

constructed your product.

We reserve the right to change the specifications of any piece of product without prior notice.

AFTER SALES SERVICE:

If you need assistance, spare parts or you are unhappy with any of the

goods please contact 

Customer Services

on:

0870 8307700

or e-mail us at:

customer.services@mamasandpapas.com

Visit our website at 

www.mamasandpapas.com 

for the latest product information.

• The bottom position of the base is the safest. You should use the cot/bed in this position as soon as your baby is

old enough to sit up. 

• Never leave anything in the cot/bed which could provide a foothold for your child to climb out or would present

a danger of suffocation or strangulation.

• All assembly fittings should be tightened properly and care should be taken to ensure that no screws are loose, a

child could trap parts of the body, or clothing (e.g. ribbons, drawstrings, necklaces ) this could pose a risk of
strangulation. 

• Regularly check that all fittings and components of the cot/bed are fully tightened and in working order. If any

parts have become worn or damaged then do not use the cot/bed, seek advice from your retailer or by calling
our Customer Services Helpline on: 0870 8307700.

• Do not use replacement parts that are not recommended or supplied by Mamas & Papas. Non-approved parts

may render the repair or cot/bed unsafe.

• Do not place your cot/bed in the close proximity of an open fire and other sources of heat, such as radiators,

electric or gas fires.

• For reasons of safety we only recommend the use of the Mamas & Papas size 400 mattress for this cot/bed.

• The mattress should be no more than 40mm shorter or narrower than the internal length or width of the

cot/bed.

• The thickness of the mattress chosen should be such that the internal height (the distance between the surface

of the mattress to the upper edge of the cot side) is a minimum of 500mm when the base is set in the lowest
position and a minimum of 200mm when the cot base is set in the highest position. 

• Your cot/bed may be cleaned with a damp cloth. 

Never use bleach or harsh abrasives.

Murano Cot-Bed V3  24/4/08  10:56  Page 16

PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor

Summary of Contents for murano cot

















Reviews: