background image

11 

 

When replacing tyres, the machine must be secured against rolling.

 

 

Repair  work  on  wheels  or  tyres  should  be  carried  out  by  persons  trained  and 
authorised  for  this  purpose.  This  work  should  be  carried  out  with  appropriately 
selected tools.

 

 

Each time the wheels are fitted, the tightness of the nuts should be checked after 
50km.

 

 3.4.

 

Transport on public roads

 

  

For  transport,  the  side  sections  of  the  TOP  cultivator  must  be  folded  into  the 

transport position using the hydraulic system. Before folding, the machine must be raised 
to the extent that the side sections do not interfere with the ground during folding.

 

During transport, the clearance under the machine should be at least 30 cm

 

While transporting the unit on public roads, it is mandatory to apply lighting equipment, 
identification 

 

emblem and reflective side lights if the rear 3-point hitch is used.

 

 

The travelling speed during transport must not be exceeded:

 

 

on roads with a smooth surface (asphalt) up to 20 km/h, 

 

on dirt or paved roads 6-10 km/h,

 

 

on bumpy roads not more than 5 km/h.

 

The driving speed must be adapted to the condition of the road and the conditions on the 
road, so that the cultivator does not bounce on the tractor's suspension system and there 
are no excessive loads on the machine frame and the tractor's suspension system.

 

Particular  care  should  be  taken  when  passing  and  overtaking  and  on  bends.  The 
permissible width of the machine running on public roads is 3.0 m.

 

 
 

WARNING! Failure to comply with the above rules may create hazards for the 
operator and bystanders as well as damage to the machine. Damage resulting 
from non-compliance with these rules is the responsibility of the user.

 

 

 3.5.

 

Description of residual risk

 

  

Mandam Sp. z o.o. makes every effort to eliminate the risk of accidents. There is, 

however, a residual risk that could result in an unfortunate accident. The greatest danger 
occurs when:

 

 

using the machine for purposes other than those described in the instructions,

 

 

using the machine by minors, persons who are not authorised, who are ill or who 
are under influence of alcohol or other drugs,

 

 

persons and animals within the operating range of the machine are present,

 

 

no caution is paid when transporting and manoeuvring the tractor,

 

 

staying on the machine or between the machine and the tractor while the engine 
is running,

 

 

operating and failure to comply with operating instructions,

 

 

driving on public roads.

 

 3.6.

 

Assessment of residual risk

 

  

Residual risk can be minimised by applying the following recommendations:

 

 

prudent and unhurried operation of the machine,

 

 

careful reading of operating instructions,

 

Summary of Contents for TOP 2.5
































Reviews: