background image

 

20 

Temperature controller 70304  |  1.02.00 

www.mc-techgroup.com

 

 

20

 

PROPER DISPOSAL OF THE DEVICE 

At the end of the life cycle of our products, it is important to take care of the appropriate disposal of obsolete 

electrical and non-electrical devices. To help protect our environment, please follow the rules and regulations of 

your country regarding recycling and waste management. 

 

 

 

21

 

SPARE PART LIST 

Temperature controller 70304 and 70304.2 

(C) Consumable parts, (R) Recommended spare parts, (S) Spare parts 

 

 

Recommended quantity 

being in operation [years]

 

 

V/E/T 

01B8401 

Electronic PID temperature controller type 70304 with self-

optimising function, front-mounting enclosure, sensor 

input:  resistance thermometer or thermocouple, output: 

0/12  V for Solid-State relay control Status signal output: 

1 contact NO for excess and low temperature alarm, Alarm 

relay switching capacity: 250 V AC, 3 A, dimensions: 48 x 48 

x 100 Power supply: 230/115 V, 50/60 Hz  

 

 

 

EZR0013 

Relais for controller 70304, 230 V AC 

 

 

 

EZR0010 

Relais for controller 70304, 110 V AC 

 

 

 

 

 

 

22

 

APPENDIX 

 

 

For further product documentation, please see our internet catalogue:  

www.mc-techgroup.com

  

Summary of Contents for 70304





















Reviews: