background image

6

Current Failure

15                     16

K2 contact is on if all the dampers are

open

14                     11

17                     18

No Failure

15                     16

K2 contact is on if the damper No. 1 is

open

14                     12

K2 contact is on if all the dampers are

closed

14    open

BKS24-9A communication and control device is used for group control and checks of 1 to 9 fire dampers with the actuator BFL

(BFN)24-T-ST in connection with the supply and communication device BKN230-24. Signalization of the damper blade position

is individual for each damper (9 LED diodes), but the dampers can be controlled and tested only as a group. BKS24-9A is intended

for use in superordinate control system, which can display operation mode and failure reports of the connected fire dampers.

BKS24-9A receives signals from BKN230-24 through two wire cable. Proper damper operation is indicated by two light LED diodes:

Control LED "OPEN" = damper blade in emergency position OPEN

Control LED "CLOSE" = damper blade in safety position CLOSED

If the damper does not reach the required position within the preset time, the appropriate on-board FAULT LED flashes and, at

the same time, the fault contact K1 is activated (K1 is group alarm for all 9 dampers). This contact is overridden as soon the

defective damper reaches the required position. The on-board FAULT LED remains on, until the fault is reset. Auxiliary contact

K2 is provided for signaling the positions of dampers to a supreme communication controlling system. The function of the auxiliary

contact can be programmed via terminal 14 according the next table.

The BKS24-9A unit can be clipped directly onto a 35mm DIN mounting rail and external wiring is connected by two 9-pin terminal

connectors.

Functional testing can be performed by pressing the TEST pushbutton. While this button is held depressed, the dampers run to

the safe position. Any malfunctions are indicated by the internal FAULT LED´s.

BAT

Summary of Contents for FDMS Series

































Reviews: