background image

15

Fire dampers are suitable for installation in arbitrary position in vertical and horizontal passages of fire separating constructions.
Damper assembly procedures must be done so as all load transfer from the fire separating constructions to the damper body is
absolutely excluded. Back-to-back air-ducting must be hung or supported so as all load transfer from the back-to-back piping to
the damper is absolutely excluded. Installation gap must be filled by approved material perfectly in all the installation space volume
(installation gap). To be able to provide inspection, inside of the fire damper is the damper with camera inspection hole standardly
equipped. For other service works, the external access door (inspection hole) must be installed on the air duct, next to the fire
damper.

The distance between the fire damper and the construction (wall, ceiling) must be minimum 75 mm. In case that two or more
dampers are supposed to be installed in one fire separating construction, the distance between the adjacent dampers must be at
least 200 mm according to EN 1366-2 paragraph 13.6.

The control mechanism has to be protected (covered) against damage and pollution during installation process. All fire dampers
has to be closed during installation process. The damper body should not be deformed in the course of bricking in. Once the
damper is built in, its blade should not grind on the damper body during opening or closing.

Collar

* Other values - see the installation details for installation

flange to flange and next to ceiling or/and wall.

4,3

4,8

5,6

6,1

6,6

7,3

8,1

9,1

10,9

11,5

14,1

17,3

20,1

23,5

28,9

98

190

313

405

12

70

123

215

353

445

2

32

90

158

250

398

490

24,5

54,5

112,5

178

270

2,5

448

540

49,5

79,5

137,5

198

290

12,5

498

590

74,5

104,5

162,5

223

315

25

558

650

104,5

134,5

192,5

248

340

37,5

628

720

139,5

169,5

227,5

278

370

52,5

Summary of Contents for FDMS








































Reviews: