3 - 12
A6 – LONGITUDINAL STABILITY LIMITER AND WARNING DEVICE
CHECK
IMPORTANT
In case of doubt during the test procedure, exit by briefly pressing the cancel button
.
The appearance of the
GAUGE
C a l i b r a t i o n
i n c o m p l e t e d
o r f a i l e d
screen indicates a failure to obey an instruction, a cancellation request
or a late response.
If in doubt, consult your dealer.
- These tests are essential for checking the correct operation and adjustment of the different components of the device.
- Place the lift truck on flat, level ground with the wheels straight.
- Hold down the test button
.
STAGE 1
TEST
P r e s s t o E n t e r
S e c u r i t y Te s t M o d e
Start of procedure.
Validate
Go to stage 2.
STAGE 2
TEST
F u l l y e x t e n t e d
t h e s t a b i l i z e r s
t h e n p r e s s
Place the lift truck with no attachments, set down the left
and right stabilisers, if provided, with the front wheels off the
ground.
Validate
Go to stage 3.
STAGE 3
TEST
R e t r a c t t e l e s c o p e
L i f t t h e b o o m t o
m a x p o s i t i o n
t h e n p r e s s
Raise the boom and retract the telescopes completely.
Validate
TEST
R e t r a c t Te l e s c o p e O K
B o o m S e n s o r N O K
S t r a i n G a u g e N O K
TEST OK
Go to stage 4.
TEST NON OK
Validate
or cancel
.
Consult your dealer.
STAGE 4
TEST
L o w e r t h e b o o m
a t f u l l s p e e d
Lower the boom with the engine running at full revs and the
hydraulic control at the maximum setting. Lowering slows
until movement is cut-off.
TEST
R e g u l a t i o n N O K
S e c u r i t y V a l v e O K
TEST OK
Go to stage 5.
TEST NON OK
Validate
or cancel
.
Consult your dealer.
STAGE 5
TEST
L o w e r t h e b o o m
u n t i l s t o p
Continue to lower the boom with the engine running at
full revs and the hydraulic control at the maximum setting.
Lowering slows until movement is next cut-off.
TEST
S e c u r i t y V a l v e N O K
TEST OK
Go to stage 6.
TEST NON OK
Validate
or cancel
.
Consult your dealer.
STAGE 6
TEST
Te s t m o v e m e n t s
t h e n i f t e s t O K :
o r t e s t N O K :
Try in the following order a reverse tilt, a forward tilt and a
telescope extension.
None of these 3 movements should be possible.
TEST OK
Validate
.
TEST NON OK
Cancel
.
Consult your dealer.
STAGE 7
TEST
Security Test
Procedure OK
End of procedure.
647104
(13/06/2016)
MT
835
/ 1135
/ 1335
ST3B
Summary of Contents for MT 1135 ST3B
