3 - 27
E3 – FUEL TANK
CLEAN
Place the lift truck on level ground with the engine stopped.
IMPORTANT
While carrying out these operations, do not smoke or work near a flame.
Never try to carry out a weld or any other operation by yourself, this could provoke an explosion or a fire.
- Inspect the parts susceptible to leaks in the fuel circuit and in the tank both visually
and by touch.
- In the event of a leak, contact your dealer.
- Place a container under drain plug 1 and unscrew the plug.
- Open the fuel filler access panel with the ignition key.
- Remove filling plug 2 to ensure that the oil is drained properly.
- Rinse out with ten litres of clean diesel through filler port 3.
- Refit and tighten the drain plug (tightening torque 29 to 39 N.m).
- Fill the fuel tank with clean diesel filtered through the filler port.
- Refit the filler plug.
- If necessary, bleed the fuel supply system (see: 3 - MAINTENANCE: H1 - FUEL SYSTEM).
1
2
3
3
5
1
2
4
E4 – GEAR BOX OIL
DRAIN
E5 – GEAR BOX OIL FILTER
CHANGE
Place the lift truck on level ground with the engine stopped, the gear box oil still warm.
IMPORTANT
Raise the boom and place the boom safety wedge on the rod of the lifting cylinder
(see: 1 - OPERATING AND SAFETY INSTRUCTIONS: LIFT TRUCK MAINTENANCE INSTRUCTIONS).
Dispose of the drain oil in an ecological manner.
Tighten the oil filter by hand pressure only and lock the filter in place by a quarter turn.
DRAINING THE OIL
- Remove cover plate 1.
- Place a container under drain plug 2 and unscrew the plug.
- Remove dipstick 3 to ensure proper emptying.
REPLACEMENT OF THE FILTER
- Unscrew and discard gear box oil filter 4, together with its seal.
- Clean the filter bracket with a clean, lint-free cloth.
- Lightly grease the new seal before refitting the new oil filter (see: 3 - MAINTENANCE:
FILTERS, CARTRIDGES AND BELTS) on its bracket.
FILLING UP THE OIL
- Refit and tighten the drain plug 2 (tightening torque 34 to 54 N.m).
- Unscrew the filler cap 5, and fill up with oil (see: 3 - MAINTENANCE: LUBRICANTS
AND FUEL) through the port, and refit the filler cap 5.
- Start the engine and leave it at idle.
- Check for possible leaks from the drain plug
and the oil filter.
- Check the correct level against the MAX mark
on the dipstick 3.
- Top up the level if necessary.
- Refit cover plate 1.
647104
(13/06/2016)
MT
835
/ 1135
/ 1335
ST3B
Summary of Contents for MT 1135 ST3B
