3 - 37
- The time taken for exhaust particle filter regeneration to complete varies (between 15 and 30 minutes) according to
various criteria, such as:
• the level of clogging of the filter,
• the ambient temperature,
• the fuel quality and type of engine oil,
• the number of exhaust particle filter automatic regeneration requests previously cancelled.
- The help screen
and the indicator light
goes off when the regeneration procedure is complete. The
engine speed returns to idle initial.
IMPORTANT
After the exhaust particle filter regeneration procedure, let the engine idle for a few minutes to lower its temperature before switching off the ignition.
H3 – WHEEL
CHANGE
For this operation, we advise you to use the hydraulic jack MANITOU reference 505507
and the safety support MANITOU reference 554772.
IMPORTANT
In the event of a wheel being changed on the public highway, secure the lift truck vicinity:
- Stop the lift truck, if possible on firm, level ground.
- Shut-down the lift truck (see: 1 - OPERATING AND SAFETY INSTRUCTIONS: DRIVING
INSTRUCTIONS UNLADEN AND LADEN).
- Switch on the warning lights.
- Immobilise the lift truck in both directions on the axle opposite to the wheel to
be changed.
- Loosen the nuts of the wheel to be changed.
- Place the jack under the flared axle tube, as near as possible to the wheel and
adjust the jack.
- Raise the wheel until it is clear of the ground and place the safety support under
the axle.
- Completely unscrew the wheel nuts and remove them.
- Free the wheel by reciprocating movements and roll it to the side.
- Slip the new wheel on the wheel hub.
- Hand-tighten the nuts, grease them if necessary.
- Remove the safety support and lower the lift truck with the jack.
- Tighten the wheel nuts with a torque wrench (see: 3 - MAINTENANCE: A - DAILY
OR EVERY 10 HOURS OF SERVICE for tightening torque).
647104
(13/06/2016)
MT
835
/ 1135
/ 1335
ST3B
Summary of Contents for MT 1135 ST3B
