3 - 38
H4 – LONGITUDINAL STABILITY LIMITER AND WARNING DEVICE
RESET
According to the use of the lift truck, the device may require to be periodically reset. This procedure simplifies the operation.
IMPORTANT
Scrupulously follow the boom positioning instructions.
The appearance of the
GAUGE
C a l i b r a t i o n
i n c o m p l e t e d
o r f a i l e d
screen indicates a failure to obey an instruction, a cancellation request
or a late response.
If in doubt, consult your dealer.
Une fois le recalage terminé, contrôler le bon fonctionnement du dispositif avertisseur et limiteur de stabilité longitudinale
(voir: 3 - MAINTENANCE: A - TOUS LES JOURS OU TOUTES LES 10 HEURES DE MARCHE).
When the reset is completed, check the operation of the longitudinal stability limiter and warning device
(see: 3 - MAINTENANCE: A- DAILY OF EVERY 10 HOURS SERVICE).
- Provide a fork carrier or a bucket and a load corresponding to at least half the lift truck's rated capacity.
- Preferably perform the reset when the lift truck is still cold (before it is used) or ensure that the temperature of the rear
axle is not more than 50 °C.
- Place the lift truck on flat, level ground with the wheels straight.
- Display the GAUGE "reset strain gauge" menu
Press to
Enter
Fast
Calibration Mode
>
< ADMIN
CALIB
ERASE
GAUGE
SECU
(see: 2 - DESCRIPTION: 6D - SCREEN DISPLAY: MENU SCREEN)
and validate
.
- Enter the CUSTOMER code
CODE
0 * * *
and validate
.
STAGE 1
GAUGE
F u l l y e x t e n d
t h e s t a b i l i z e r s
t h e n p r e s s
Fully extend the stabilizers.
MT 1135 ST3B / MT 1335 ST3B
Validate
STAGE 2
GAUGE
R e t r a c t t e l e s c o p e
L i f t t h e b o o m t o
m a x p o s i t i o n
t h e n p r e s s
Fully raise the boom with the telescopes fully retracted.
Validate
STAGE 3
GAUGE
W a i t c a l i b r a t i o n
i n p r o g r e s s . . .
Calibration in progress…
Go to stage 4.
STAGE 4
GAUGE
C o m p l e t l y l o w e r t h e
b o o m o n t h e f r a m e .
t h e p r e s s
Fully lower the boom with the engine running at full revs and the hydraulic
control at the maximum setting.
Validate
STAGE 5
GAUGE
R i s e s t a b i l i z e r s ,
t h e n p r e s s
Fully raise the stabilizers.
MT 1135 ST3B / MT 1335 ST3B
Validate
STAGE 6
GAUGE
E x t e n d t h e b o o m
u n t i l r e a r a x l e i s
l i f t e d t h e n w a i t 5 s
a n d p r e s s
/
With the fork carriage or the bucket and a load. Boom fully retracted in
the lowered position, approximately 20 centimetres from the ground.
/
Keep the load as close to the ground as possible throughout this operation.
Hold down the disable the "aggravating" hydraulic movement cut-off
button
(indicator lamp lit), and telescope the boom until the rear
wheels leave the ground.
Wait 5 seconds
and validate
FINISH
GAUGE
R e t r a c t t h e b o o m
t h e n p r e s s t o s t o r e
n e w c a l i b r a t i o n
Perform telescope retraction to restore the situation.
Validate
to record the new
parameters
647104
(13/06/2016)
MT
835
/ 1135
/ 1335
ST3B
Summary of Contents for MT 1135 ST3B
