3-32
G - OCCASIONAL MAINTENANCE
G1 - FUEL SYSTEM
BLEEDING
These operations are only to be carried out in the following cases:
- A component of the fuel system replaced or drained.
- A drained tank.
- Running out of fuel.
Ensure that the level of fuel in the tank is sufficient and bleed in the following order:
BLEEDING THE FUEL FILTER
- Open the I.C. engine bonnet.
- Place a receptacle under drain port 1 (fig. G1/1).
- Unscrew ring 2 (fig. G1/1) by two or three thread turns to drain the water from the water trap.
- Retighten ring 2 (fig. G1/1).
BLEEDING THE INJECTION PUMP
- Untighten bleeder screw 3 (fig. G1/2) by two to three thread turns.
- Switch on the lift truck ignition until the diesel oil flows from the bleeder screw free of any air.
- Tighten the bleed screw while the diesel fuel is flowing out.
The I.C. engine is ready to be started up.
NOTE: If the I.C. engine runs properly for a short time then stops or runs unevenly, check for
possible leaks in the low pressure circuit. If in doubt, contact your dealer.
G2 - WHEEL
CHANGE
In the event of a wheel being changed on the public highway, ensure the following:
For this operation, we advise you to use the hydraulic jack MANITOU reference 505507 and the
safety support MANITOU reference 554772.
- Stop the lift truck, if possible on even and hard ground.
- Stop the lift truck (see: 1 - OPERATING AND SAFETY INSTRUCTIONS: DRIVING INSTRUCTIONS
UNLADEN AND LADEN).
- Put the warning lights on.
- Immobilise the lift truck in both directions on the axle opposite to the wheel to be changed.
- Unlock the nuts of the wheel to be changed.
- Place the jack under the flared axle tube, as near as possible to the wheel and adjust the jack
(fig. G2/1).
- Lift the wheel until it comes off the ground and put in place the safety support under the axle
(fig. G2/2).
- Completely unscrew the wheel nuts and remove them.
- Free the wheel by reciprocating movements and roll it to the side.
- Slip the new wheel on the wheel hub.
- Refit the nuts by hand, if necessary grease them.
- Remove the safety support and lower the lift truck with the jack.
- Tighten the wheel nuts with a torque wrench (see: 3 - MAINTENANCE: A - DAILY OR EVERY 10
HOURS OF SERVICE for tightening torque).
G2/1
G2/2
G1/2
3
G1/1
2
1
647421
(22/08/2017)
MT-X
625
Série
2-E3
+
COMFORT
Summary of Contents for MT-X 625 2-E3 Series
