1
1
1
2
7
3
F2 – SAFETY DRY AIR FILTER CARTRIDGE
REPLACE
- For the disassembly and reassembly of the dry air filter cartridge, see: 3 -
MAINTENANCE: E1 - AIR FILTER CARTRIDGE.
- Gently remove the dry air filter safety cartridge 1, taking care to avoid spilling the dust.
- Clean the gasket surface on the filter with a damp, clean lint-free cloth.
- Check the condition of the new safety cartridge before fitting (see: 3 - MAINTENANCE:
FILTERS AND BELTS).
- Insert the cartridge in the filter axis and push it home, pressing against the outer
edge and not the center.
IMPORTANT
The safety cartridge replacement frequency is given for information only. It must be changed every second time the
dry air filter cartridge is changed.
F3 – WHEEL NUTS TIGHTENING TORQUE
CHECK
- Check the condition of the tires, to detect cuts, blisters, wear, etc.
- Check the tightening torque of the wheel nuts with a torque wrench.
• Front tires: 630 N.m ± 15 %
• Rear wheels: 630 N.m ± 15%
F4 – HYDRAULIC OIL
DRAIN
F5 – HYDRAULIC OIL TANK SUCTION STRAINER
CLEAN
F6 – HYDRAULIC TANK
CLEAN
F7 – HYDRAULIC FLUID TANK FILTER CAP
REPLACE
F8 – DISTRIBUTOR CONTROL HEAD FILTER
REPLACE
Place the lift truck on level ground with the engine stopped, and the boom retracted
and lowered as far as possible.
IMPORTANT
Before carrying out any work, thoroughly clean the area around the filter, the drain plugs and the inlet cover on the
hydraulic tank.
Dispose of the drain oil in an ecological manner.
Use a very clean container and funnel and clean the top of the oil drum before filling.
DRAINING THE OIL
- Place a container under the drain plugs 1 and unscrew them.
- Remove level and filling plug 2 to ensure that the oil is drained properly and discard.
CLEANING THE STRAINER AND THE TANK
- Remove the inlet cover 3.
- Remove and clean the suction strainer using a compressed air jet, check its condition
and replace if necessary (see: 3 - MAINTENANCE: FILTERS CARTRIDGES AND BELTS).
- Before refitting the strainer, clean the bottom of the tank with a clean, lint-free cloth.
- Clean by bringing the cloth towards the strainer opening and remove any residue
from the bottom of the tank.
- Refit the strainer and tighten the inlet cover 3 (tightening torque 81 N.m) making
sure the seal is in the correct position.
3 - 31
647449
(30/11/2015)
MT
732/932
ST3B
Summary of Contents for MT732ST38
