background image

Section 5

Before Calling For Service

 Part Number 80-1561-3

5-1

Section 5

Before Calling For Service

Checklist

If a problem arises during operation of your ice machine, follow the checklist below before calling service. Routine 
adjustments and maintenance procedures are not covered by the warranty.

Problem

Possible Cause

To Correct

Ice machine does not operate.

No electrical power to the ice machine 
and/or condensing unit.

Replace the fuse/reset the breaker/turn 
on the main switch.

ICE/OFF/CLEAN toggle switch set 
improperly.

Move the toggle switch to the ICE 
position.

Water curtain stuck open.

Water curtain must be installed and 
swinging freely. (See Section 4)

Ice machine stops, and can be restarted 
by moving the toggle switch to OFF and 
back to ICE.

Safety limit feature stopping the ice 
machine.

Refer to “Safety Limit Feature” on the 
next page.

Ice machine does not release ice or is 
slow to harvest.

Ice machine is dirty.

Clean and sanitize the ice machine. 
(See Section 4)

Ice machine is not level.

Level the ice machine. (See Section 2)

Low air temperature around ice machine 
head section.

Air temperature must be at least 35°F 
(1.6°C).

Ice machine does not cycle into harvest 
mode.

The six-minute freeze time lock-in has 
not expired yet.

Wait for the freeze lock-in to expire.

Ice thickness probe is dirty.

Clean and sanitize the ice machine. 
(See Section 4)

Ice thickness probe is disconnected.

Connect the wire.

Ice thickness probe is out of adjustment.

Adjust the ice thickness probe. 
(See Section 3)

Uneven ice fill (thin at the top of 
evaporator).

Verify sufficient water level in sump 
trough. Contact a qualified service 
company to check refrigeration system.

Ice quality is poor (soft or not clear).

Poor incoming water quality.

Contact a qualified service company to 
test the quality of the incoming water and 
make appropriate filter 
recommendations.

Water filtration is poor.

Replace the filter.

Ice machine is dirty.

Clean and sanitize the ice machine. 
(See Section 4)

Water dump valve is not working.

Disassemble and clean the water dump 
valve. (See Section 4)

Water softener is working improperly (if 
applicable).

Repair the water softener.

Summary of Contents for S1000M







































Reviews: