background image

Part Number 000001590 Rev03 11/19 25

Section 4 

Maintenance

WATER SHUTTERS

The water shutter is designed to keep the spraying water 

from escaping the evaporator compartment.
TO REMOVE JUST THE WATER SHUTTERS:

1.  Grasp one end of the water shutter and lift up.
2.  Pivot water shutter and disengage remaining end.
3.  To re-install into ice machine, grasp one end of the water 

shutters, install one end, pivot the opposite end and 

pull down into position. Make sure tabs are secure in 

grooves.

TO REMOVE WATER SHUTTER ASSEMBLY:

1.  Slide evaporator bucket forward 1/2” (13 mm).
2.  Lift shutter assembly straight up.

n

Warning

Removing the water shutters while the water pump 

is running will allow water to spray from ice machine. 

Disconnect electrical power to the ice machine at the 

electric service switch box and turn off the water supply.

ICE CHUTE

The ice chute is positioned over the spray nozzles and allows 

the ice to easily fall into the bin. It must be firmly positioned 

over the spray bar, with the front edge inside the water 

trough. Spray nozzles must be align with the spray holes or 

spray water will fall into the bin.

1.  Grab protruding spray hole on one end and lift up and 

remove.

2.  To re-install ice chute, grasp protruding spray hole and 

position over Water Distribution Assembly.

Make sure rear supports are over spray bar, and front edge is 

inside of water trough.

Summary of Contents for SM Series

































Reviews: