background image

Part Number 000001590 Rev03 11/19

Table of Contents

 (continued)

Section 3

Operation

Component Identification ................................................................................................ 17

Control Panel ................................................................................................................... 18

Functions .......................................................................................................................18

Safety Timers .................................................................................................................18

Sequence of Operation .................................................................................................... 19

Operational Checks ......................................................................................................... 19

Water Level ...................................................................................................................19

Bin Thermostat Adjustment ..........................................................................................19

Testing And Adjusting The Bin Thermostat ...................................................................20

Cube Weight Adjustment ................................................................................................. 20

Additional Finishing Time Check: ..................................................................................20

Adjusting Finishing Time ...............................................................................................20

Section 4

Maintenance

Interior Cleaning and Sanitizing ....................................................................................... 21

General ..........................................................................................................................21

Cleaning and Sanitizing Procedures ................................................................................. 21

In Place Cleaning/Sanitizing Procedure ............................................................................ 22

Cleaning Procedure ......................................................................................................... 23

Removal of Parts for Cleaning/Sanitizing ......................................................................... 24

Top Cover ......................................................................................................................24

Water Shutters ..............................................................................................................25

Ice chute ........................................................................................................................25

Sump Drain Overflow tube ............................................................................................26

Water Trough ................................................................................................................26

Spray Bar, Water Pump and Hose..................................................................................26

Spray Bar Disassembly ..................................................................................................26

Bin Light ........................................................................................................................27

Front Grill ......................................................................................................................27

Water Filter ...................................................................................................................27

Ice Machine Inspection .................................................................................................28

Exterior Cleaning ...........................................................................................................28

Cleaning the Condenser ................................................................................................28

Removal from Service/Long Term Storage/Winterization ................................................. 28

Section 5

Troubleshooting

Checklist .......................................................................................................................... 29

Safety Limit Feature......................................................................................................... 30

Summary of Contents for SM Series

































Reviews: