background image

IMPORTANT 

It is recommended that bathers should limit their use of the whirlpool to not more than 20 minutes in any 

one bathing session.

OPERATION

BUTTON 1, WHITE LIGHT - POWER ON/OFF

  The first button is the power button which will activate the 

keypad and illuminate in dim colors.

BUTTON 2, BLUE LIGHT - PUMP

  Push the 

button once to activate blower, push again 

to turn off.

BUTTON 3, YELLOW LIGHT - LIGHT  SYSTEM

 

Push the button once to activate the light 

system.    Continue  to  push  button  until 

desired color is reached or lights are turned 

off.  Push and hold button for two seconds 

to power off immediately.

BUTTON 4, RED LIGHT  - SURFACE HEATER 

(if equipped)

  Push the button once to activate the heated seat and backrest, push again to turn off.

RESTORE ACR Combination - Model 8690 or 8790

IMPORTANT 

It is recommended that bathers should limit their use of the air system or whirlpool to not more than 20 

minutes in any one bathing session.

OPERATION

BUTTON 1, WHITE LIGHT - POWER ON/OFF

  The first button is the power button which will activate the 

keypad and illuminate in dim colors.

BUTTON 2, BLUE LIGHT - PUMP

  Push the 

button once to activate blower, push again 

to turn off.

BUTTON 3, GREEN LIGHT - BLOWER

  Push 

the  button  once  to  activate  blower,  push 

again to turn off. 

BUTTON 4, YELLOW LIGHT - LIGHT  SYSTEM

 

Push the button once to activate the light 

system.    Continue  to  push  button  until 

desired color is reached or lights are turned 

off.  Push and hold button for two seconds to power off immediately.

BUTTON 5, RED LIGHT  - SURFACE HEATER (if equipped)

  Push the button once to activate the heated seat 

and backrest, push again to turn off.

USE AND CARE GUIDE

The 

Adjustable Jet

 can be adjusted for the optimal water flow.  Turning the 

face plate clockwise increases water flow and counter clockwise decreases 

water flow.

The 

Jet Nozzle

 is also adjustable by moving the nozzle which changes the 

direction of the water flow.  This allows various body areas to be targeted 

for a therapeutic hydro-massage.

RESTORE ACR Whirlpool Bath - Model 8090 or 8190

Summary of Contents for Restore ACR 8090

















Reviews: