background image

USER MAINTENANCE INSTRUCTIONS

CODE COMPLIANCE

USE AND CARE GUIDE

See Soaking Tub section for instructions on entering, filling and exiting the bath.

IMPORTANT 

It is recommended that bathers should limit their use of the air bath to not more than 

20 minutes in any one bathing session.

OPERATION

ON/OFF BUTTON - 

Press button once to power on, press again to power off.

NOTE:

Before activating, check prime port to ensure the system is primed.  When primed, there will be no air bubbles 

exiting the port.  System is ready to be activated.

RESTORE ACR MicroDerm Therapeutic Bath - Model 8890 or 8990

Ozonator

Whirlpools  and  Combination  baths  are  equipped  with  Ozonators.    The  ozonator  will  emit  ozone  into  the 

whirlpool piping system which will eliminate bacteria growth.  It will discharge approximately twelve hours 

from the time it was plugged into the receptacle, and will discharge every twelve hours afterwards.

Whirlpool and Air bath

The whirlpool and air bath systems require routine cleaning to sanitize the system.  Twice per month, or more 

depending on usage, clean the whirlpool by following the directions below:

 

a.  Fill the tub with hot water.

 

b.  Add two (2) tablespoons of automatic dishwasher detergent and 1/2 cup of bleach to the water.

 

c.  Run whirlpool for at least 15 minutes.

 

d.  Drain, refill with cold water, operate for 10 minutes.

 

e.  Drain and wipe with a soft cloth.

Surface cleaning

Wash all surfaces of the bathtub with a mild solution of vinegar and water.  Alternately, the surface can be 

washed with non-abrasive household cleaners.  Oily or greasy spots can be lifted with denatured alcohol.  Wipe 

off with clear, warm water and dry with a soft cloth.

Accepted  by  the  “Swimming  Pool 

Research 

Committee” 

of 

the 

International  Association  of  Plumbing 

and  Mechanical  Officials  as  meeting 

the requirements of the Uniform 

Swimming Pool Code.

Accepted  by  the  “Plumbing  Research 

Committee”  of  the  International 

Association 

of 

Plumbing 

and 

Mechanical  Officials  as  meeting  the 

requirements of the Uniform Plumbing 

Code.

ETL Listed (Complies with U.L. Standard 

1795).    Hydromassage  Bathtub  Listed 

3129295

Summary of Contents for Restore ACR 8090

















Reviews: