background image

 

 

 

 

The manufacturer or supplier shall not be liable for any damage resulting from the use of other 
products. If replacing the product, only use MANTION SMT or MANTION SMT-approved products. 

 

Radio control: 

 
Use of the wireless remote control is only authorized if any disturbance in the transmitter or 
receiver poses no danger to people or animals, or if such hazards are removed by other 
arrangements. 
The user of the wireless control is not protected against interference generated by other 
telecommunications installations and remote-controlled devices. If there is a high level of 
interference, contact the organization in charge of measuring wireless interference (radiolocation). 
Do not use the radio transmitter in places sensitive to radio transmissions (airports, hospitals) or 
only after taking all the necessary precautions. 
The swing shutter remote control may pose risks and for this reason please heed the following 
points when using it: 
 

1.  Make sure no object or person is within range of the swinging shutters. 
2.  Only operate them when direct visual inspection is possible. 

 

The wireless control is not a toy; do not let children play with it. Keep it out of reach of children and 
animals. 

 
Terms of the guarantee  

 
MANTION SMT products come with a 5 (five) years guarantee from the date of delivery. 
 
The guarantee is limited, as decided by MANTION SMT, either to replacement or to repair of 
products MANTION SMT recognizes as faulty, with the proviso that: 
 

1.  Subject to MANTION SMT's written permission to return the products, the said products are 

returned to MANTION SMT forthwith with the details of the fault and a copy of the 
installation engineer or dealer's bill stating the date of installation. 

 

2.  The products have been stored, installed, maintained and used in accordance with 

MANTION SMT's instructions and specifications. 

 
The guarantee is strictly limited to the provisions of this clause, and any other guarantee or 
liability, including loss of profits or damage directly or indirectly resulting from the sale or use of the 
products, is excluded. 
 
MANTION SMT shall on no account be liable for drilling and embedding conditions. 
 
MANTION SMT shall in any event only be liable for the WIBAT product. The guarantee does not 
apply in case of overvoltage or short-circuiting resulting for instance from connection errors, 
weather conditions such as lightning etc. The guarantee does not cover normal wear. 

 

 
 
 
 
 
 

Summary of Contents for SMT WIBAT





























Reviews:

Related manuals for SMT WIBAT