background image

2

Mareli Systems

Observing the prescriptions of the present manual is in the user’s favour and is one of the war-

ranty conditions. Compliance with this instruction is in the interest of the consumer and one of 

the warranty terms.

I

NSTRUCTIONS FOR SECURITY:

•  This appliance is not intended for use by people (including children) with limited physical, sensory or 

mental abilities or lack of experience and knowledge. The installation must be performed by a qualified 

expert in the field of heating installations or authorized by “Marelli Systems’ service. The place and way of 

connecting the stove should be selected carefully in accord with the safety instructions. Install away from 

flammable objects!

•  Before starting any operation, the user must read and fully understand the contents of this instruction 

manual. Incorrect setup may cause hazardous conditions and / or incorrect function of the stove;

•  Do not wash the stove with water. Water can get inside the fireplace and damage the electronics and 

cause an electric shock;

•  Do not put clothes to dry on the stove. Any clothes hangers and other objects must be located within a 

reasonable distance from the fireplace. Fire hazard;

•  The user is fully responsible for the proper use of the product which exempts the company from liability 

of any users errors or misbehaviour or omissions;

•  Any intervention or replacement that is made by unauthorized people or using non original spare parts 

for the product can be risky for the user and release the company from all liability;

•  Most surfaces of the stove are extremely hot (the door handle, glass, flue pipe, etc.). Avoid contact with 

these parts before assuring yourself that you us temperature resistant gloves as well as suitable temperature 

resistant instruments;

•  Under no circumstances should the fire be ignited with the door open or broken glass;

•  The product must be electrically connected to a system equipped with an effective earth conductor. 

(Must be grounded);

•  Turn off the stove in case of failure or malfunction;

•  All unburned pellets in the burner after each unsuccessful attempt ignition must be removed before a 

new ignition;

•  When installing the product all fire safety requirements must be respected

If there is a fire in the flue pipe, extinguish the stove, disconnect the power cord and never open the door. •  

•  Call competent authorized service technicians;

•  Do not light the stove with flammable materials if the ignition system failed;

•  Periodically check and clean the smoke outlet ducts of the stove (connection to the flue pipe);

•  Pellet stove is not a cooker;

•  Always keep the cover closed;

SAFE DISTANCES:

When installing the product a safe distance of at least 600 mm must be respected. This distance 

applies to the product located near materials of B or C flammability level. The safe distance is 

doubled if the product is close to materials of C3 combustion level.

Summary of Contents for PS 24

















Reviews: