background image

Note: The remote vehicle location system is active 30 seconds after the alarm is armed. 

1. Press the       button to active the vehicle locator system. The horn/siren will beep 2 times and

the parking lights will flash 3 times. This operation will repeat a second time. 

2. Press the       button again within 30 seconds. The horn/siren will beep 3 times and the parking

lights will flash 3 times. This operation will repeat a second time.

3. Press the       button again within 30 seconds. The horn/siren will beep 6 times and the parking

lights will flash 6 times. 

The transmitter can be used as a remote panic switch to manually trigger the alarm system in case

of an emergency.

1. Press and hold the     button for 3 seconds. The security system will begin to sound and the

parking lights will begin to flash. The        icon will display in the LCD transmitter display. 

2. During panic mode, the normal functions of this transmitter becomes temporarily inoperable.

The transmitter    and    buttons can be used to lock and unlock the door (if the option is

installed), however, once the    button is pressed, the vehicle’s starter disable device, will be

enabled allowing the vehicle to start.

3. To stop the panic alarm, press the      transmitter button , the panic mode will be turned off 

immediately.

4. If the       button is not pressed, the alarm will automatically stop after 30 seconds.

When armed, your vehicle is protected as follows:

1. Light impact will trigger the warn-away signal.

2. Heavy impacts, doors open, hood open, trunk open or ignition key activated will trigger the

programmed sequence. The starter disable relay prevents the vehicle’s starter from cranking.

The siren, horn, parking lights and dome light will turn on to alert of an intrusion for 30

seconds. If one of the sensors or detectors are still active, the security system will sound a

maximum of 6 times for 30 seconds.

Trigger the System

Remote Panic Function

Progressive Remote Vehicle Locator System

10

Doors

Triggered

Ignition

Triggered

ARM

IGN

ARM

ARM

H

O

O

D

T

R

U

N

K

ARM

Trunk / Hood

Triggered

Warn Away

Triggered

Shock Sensor

Triggered

Summary of Contents for MARKSMAN X11

























Reviews: