2
©
MARMITEK
SAFETY WARNINGS
• To prevent short circuits, this product should only be used inside and only in dry spaces. Do not expose the components to rain or
moisture. Do not use the product close to a bath, swimming pool etc.
• Do not expose the components of your systems to extremely high temperatures or bright light sources.
• In case of improper usage or if you have altered and repaired the product yourself, all guarantees expire. Marmitek does not accept
responsibility in the case of improper usage of the product or when the product is used for purposes other than specified. Marmitek
does not accept responsibility for additional damage other than covered by the legal product responsibility.
• This product is not a toy. Keep out of reach of children.
• Do not open the product (battery panel excepted): the device may contain live parts. The product should only be repaired or
serviced by a qualified repairman.
• Keep batteries out of the reach of children. Dispose of batteries as chemical waste. Never use old and new batteries or different
types of batteries together. Remove the batteries when you are not using the system for a longer period of time. Check the polarity
(+/-) of the batteries when inserting them in the product. Wrong positioning can cause an explosion.
• Only connect the adapter to the mains after checking whether the mains voltage is the same as the values on the identification
tags. Never connect an adapter when it is damaged. In that case, contact your supplier.
• Automatic switching devices provide comfort, but can also be dangerous. They can surprise people or can ignite clothing hanging
over an electric heat source. Please be careful and take appropriate measures to avoid accidents.
INTRODUCTION
Congratulations on purchasing the Marmitek My Happy Home set, a complete system to manage your home.
This manual will help you on your way. More information about the individual modules can be found on our web site:
www.marmitek.com. Here you can find answers to frequently asked questions (support). All modules of the Marmitek X-10 system
can be bought separately. You can extend your starter set at any time with any required component.
Marmitek X-10 components use the existing mains wiring to communicate (using Marmitek X-10 signals). You can build a complete
system using the three different kinds of components of the Marmitek X-10 System:
1. Modules:
These components will receive Marmitek X-10 signals and will switch or dim the attached lamp or appliance.
2. Controllers:
These components will transmit Marmitek X-10 signals and thus will control the Modules.
3. Transmitters:
Wireless components like remotes. The signals of these components will be received by a controller with
transceiver functionality (IRRF 7243, TM13 or console of a Marmitek Security System). The Transceiver will
translate the signals into Marmitek X-10 signals on the power line.
INSTALLING THE COMPLETE SYSTEM IN 8 STEPS*
Step 1
Installing the TM13 Transceiver Module
• Plug the small appliance (i.e. a radio or lamp) into the socket of the TM13*. Make sure the
appliance itself is turned on.
• Place the TM13 in a wall socket.
• Put the antenna in the upright position.
The UnitCode cannot be set and will always be ‘1’.
Step 2
The Remote Control EasyControl8
Insert 2 AAA batteries in the battery slot of the remote control*. Make sure the + and – are placed correctly.
Step 3
You can now control the appliance connected to the TM13 Transceiver with the remote control
• Press the Marmitek X-10 button (home icon).
• Press button 1.
• Press ON (PROG +).
• The appliance connected to the TM13 is now switched on.
• Press OFF (PROG -).
• The appliance is switched off.
Step 4
Installing the LM12 Lamp Module
1. Use a screwdriver to set the black dial to number 2 (this is the UnitCode. This code indicates which button of
the remote control responds to the dimmer module). The red dial should remain set to A (this is the HouseCode.
This code needs to be the same for each module).
2. Plug the Module into a wall socket.
3. Plug an incandescent lamp into the Module (min. 40W – max. 300W).
Step 5
You can now remotely control the lamp connected to the LM12
• Press the Marmitek X-10 button (home icon).
• Press button 2.
• Press ON (PROG +).
• The lamp connected to the LM12 will switch on.
• Press DIM and keep the button pressed for a few seconds (Volume -).
• The lamp dims.
• Press OFF (PROG -).
• The lamp is switched off.
