background image

©MARMITEK

12

DECLARATION OF CONFORMITY 

Hereby, Marmitek BV, declares that this RoboDome10 is in compliance with the essential 

requirements and other relevant provisions of the following Directives: 

DIRECTIVE 2004/108/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 15 

December 2004 on the approximation of the laws of the Member States relating to 

electromagnetic compatibility 

Directive 2006/95/EC of the European Parliament and of the Council of 12 December 2006 on the 

harmonisation of the laws of Member States relating to electrical equipment designed for use 

within certain voltage limits 

Directive 2002/95/EC of the European Parliament and of the Council of 27 January 2003 on the 

restriction of the use of certain hazardous substances in electrical and electronic equipment 

Commission Regulation (EC) No 278/2009 of 6 April 2009 implementing Directive 2005/32/EC of 

the European Parliament and of the Council with regard to ecodesign requirements for no-load 

condition electric power consumption and average active efficiency of external power supplies 

MARMITEK BV - P.O. BOX 4257 - 5604 EG EINDHOVEN – THE NETHERLANDS

Copyrights 

Marmitek is a trademark of Pattitude BV 
RoboDome10 is a trademark of Marmitek B.V.

 All rights reserved.

Copyright and all other proprietary rights in the content (including but not limited to model numbers, 
software, audio, video, text and photographs) rests with Marmitek B.V. Any use of the Content, but 
without limitation, distribution, reproduction, modification, display or transmission without the prior 
written consent of Marmitek is strictly prohibited. All copyright and other proprietary notices shall be 
retained on all reproductions. 

Summary of Contents for robodome10

















Reviews: