background image

water line

To avoid buildup of oils and lotions at the water line, clean the interior weekly or 

when needed. We suggest the Glove Sponge to clean without scratching. 

note:

 Do not use the same brush or sponge to clean the exterior of the ves-

sel and the interior of the vessel. Soap and other product residue used on the 

outside of the vessel can cause foaming of the vessel water and scratches to 

the vessel surface if used on the inside of the vessel. 

suspenDeD use or winteriZing tHe vessel

If you decide to discontinue the use of your vessel for any extended period of 

time, we suggest you follow the steps below. 

note: 

During long periods of inactivity, damage can occur to equipment 

from condensation within the equipment compartment. Failure to follow these 

instructions during freezing conditions will result in cracked fitting(s) and glue 

joints, and other damage.

1.  Turn off the power to the vessel.  

2.  Drain the vessel. (See DRAINING AND REFILLING THE VESSEL.)

3.  Remove all residual water from the seating and footwell.  If necessary, 

bail out  the remaining water then dry the vessel with towels.  A wet/dry 

vacuum is recommended for best results.

4.  Using the wet/dry vacuum, place vacuum nozzle over each jet nozzle to 

remove water from plumbing lines, starting with the highest jet and finishing 

with the lowest jet. 

note: 

The vessel is equipped with a Tri-Zone control 

which is used to divert water between different jet zones. The valve must 

be “open” to the particular jets you are vacuuming. 

5.  Unscrew the pump plugs from the pumps. (See STARTING YOUR Vessel.)

6.  Again, using the wet/dry vacuum, place nozzle over the exposed pump 

openings to remove excess water. The pumps should be removed from 

the vessel and stored in a climate-controlled room. 

7.  Clean the vessel interior. 

8.  Clean the filter cartridges.

9.  Reinstall the DuraCover™ and lock in place. 

note: 

Direct sunlight on the 

vessel surface can cause severe damage or blemishing and can result in 

the voiding of any surface warranties. 

vACAtion CAre instruCtions

short time periods: 3-5 days

1.  Adjust the pH (see WATER CARE).

2.  Sanitize the water by following the shock procedures (See WATER CARE).

3.  Lock your vessel cover in place with cover locks.

4.  Upon return, shock sanitize water.

long time periods: 5-14 days

1.  One day before leaving, set the temperature to its lowest level (approxi-

mately 80°F, 27°C).

2.  Adjust pH as needed.

3.  Shock sanitize water.

4.  Upon return, shock sanitize water. 

5.  Return temperature to original setting.

6.  Test water chemistry and adjust as necessary.

MARQUIS

®

 ATV MAInTenAnce

Summary of Contents for ATV-14






































Reviews: