EVERY THREE TO FOUR MONTHS
Draining and Filling the Spa
The average spa needs to be drained every three to four months. After
months of continually adding chemicals to the water and introducing body
oils and lotions, the water can be difficult to manage and chemicals are not
as effective as usual. You may also notice excessive foaming. More frequent
draining may be required dependent on use.
Draining the Spa
1. Turn off the power to the spa.
2. Open the equipment compartment (see EQUIPMENT DIAGRAM). Re-
move the hose bib cap from the connection and attach a hose.
3. Open the drain valve. Gravity causes the water to drain out of the hose.
4. When the spa is empty, close the drain valve and remove the hose. Rein-
stall the hose bib plug.
NOTE:
Keep the drain valve closed at all times except when draining the
spa (do not rely on the cap to stop the flow of water). Not doing so could
result in damage to the drain valve due to freezing water.
Replacing the Mineral Cartridge
The
Spa Frog
®
mineral or @ease mineral cartridge
should be replaced every
three to four months. You may still feel the “spent” minerals inside, but they
are no longer effective and need to be replaced. (See ADJUST THE MIN-
ERAL CARTRIDGES, Blue Mineral Cartridge.)
Clean the DuraShell
®
Interior
Once the spa is drained, clean the DuraShell
®
interior thoroughly – especially at
the water line. We suggest the
Glove Sponge
to clean without scratching.
Marquis
®
Spa Brite or Gloss and Guard
are the recommended cleaning agent
for DuraShell
®
– other products should be avoided except as stated below.
To maintain the high gloss and elegant look of DuraShell
®
, just follow these
simple steps: For normal care and cleaning use a soft cloth or sponge and
water. Rinse well and dry with a soft, clean cloth. Never use abrasive clean-
ers. Do not allow your acrylic surface to come into contact with products
such as ketones or esters such as acetone or ethyl acetate (nail polish
remover), Wintergreen oil (methyl salicylate), nail polish, dry cleaning solution
or other chlorinated organic solvents, lacquer thinners, gasoline, aromatic
solvents, citrus cleaners, pine oil, etc. Remove dust and dry dirt with a soft,
damp cloth. Clean grease, oil, paint and ink stains with diluted isopropyl (rub-
bing) alcohol (do not let alcohol pool or remain on acrylic). Dry with a clean,
soft cloth. Avoid using razor blades or other sharp instruments that might
scratch the surface.
NOTE:
Due to the high-gloss, fine finish of the acrylics, imperfections in the
surface texture may occur. A natural aging process in acrylic can lead to a
process called crazing. Fine spider web-like lines can form on the cosmetic
surface of acrylic over time after exposure to the elements and chemicals.
VECTOR21 MAINTENANCE
44
Summary of Contents for V65L
