SANITIZE
ConstantClean™ System
The ConstantClean™ system utilizes a combination of sanitizers to increase
water quality and significantly decrease maintenance. The combination of
a
Spa Frog
®
Cartridge system or @ease Chlorine system
* and the factory
installed ozonator greatly reduce the amount of sanitizer required. Instead of
the normal 3 - 5 ppm of bromine or chlorine, you may only need to maintain
1 - 2 ppm of bromine or chlorine at .5 - 1 ppm.
NOTE:
The use of
Spa Frog
®
floating cartridges or @ease Smartchlor
is
recommended. Do not use other floating chemical dispensers or Biguanide.
Damage to the spa shell and other internal components can occur.
* The built-in sanitation system is not available in some international markets.
However, the ozone system is available on all spa models in all countries.
Please see your dealer for recommended alternate treatment method if the
built-in sanitation system is not available.
BUILT-IN SANITATION SYSTEM*
After the spa has been brought to set temperature and the balance has
been established, Shock-sanitize the spa. Then it is time to install the S
pa
Frog
®
or
@ease with SmartChlor Chlorine
and mineral cartridges.
ADJUST THE MINERAL CARTRIDGE
Remove the protective cellophane wrap from the blue
Spa Frog
®
or @ease
mineral cartridge
. While holding the bottom of the cartridge, turn the top
until the number six appears in the setting window. Install into the holder
NOTE:
The mineral cartridge should be replaced every three to four
months. You will still feel the “spent” minerals inside, but they are no longer
effective and the cartridge needs to be replaced. It is recommended to
drain and refill the spa at the same time you replace the mineral cartridge.
ADJUST THE SANITIZING CARTRIDGE
Remove the protective cellophane wrap from the
Spa Frog
®
bromine car-
tridge or @ease Chlorine cartridge
. Finding the right setting for the sanitizing
cartridge will require monitoring your usage for the first few weeks. Begin
with an initial setting based on the chart below and monitor sanitizer levels
daily for the first week or so, adjusting the cartridge by one setting per day
until a .5 - 2 ppm level has been achieved depending on whether you are
using bromine or chlorine. To adjust cartridge, remove from system and turn
to the next highest setting if the bromine level is low or the next lower set-
ting if the santizer level is high. The sanitizing cartridge needs to be replaced
when empty between two and four weeks. Install the cartridge only after
the spa has been balanced, brought to temperature and sanitized.
Suggested
Initial
Sanitizer Cartridge Settings
Daily filter time
Spa Gallons
-250
250-300 300-400 400-500
One hour
2
2
3
4
Two hours
2
2
2
3
Four hours
1
1
2
2
VECTOR21 SPA CARE GUIDE
50
Summary of Contents for V65L
