5
4
Footcontroller
(optional-PEDL-90008)
Footcontroller Factory Settings
Footswitch 1: Clean/Crunch Switch
Footswitch 2: OD-1/OD-2 Switch
Footswitch 3: Tap Tempo Switch
Footswitch 4: Tuner
Programming
The footswitch can be programmed to store front
panel switches (Switch Store) or complete presets
(Preset Store).
Switch Store
To assign a front panel switch to a Footswitch location
(1), press and hold the front panel switch and while
held down press the Footswitch (1) you wish to assign
it to.
The Digital Display (3) will swirl to show that the
footswitch has been assigned. You can then release
the footswitch and front panel switch.
Preset Store
To assign a preset to a Footswitch
(1), select the
required channel and modify the front panel controls
if required, press and hold the Store switch on the
front panel and while held down, press your chosen
Footswitch (1).
The Digital Display (3) will swirl to show that the
footswitch has been assigned. You can then release
the footswitch and Store switch.
Footcontroller Presets are independent of the
dedicated Channel presets stored within the
amplifier. This allows you to create a number of
presets based on the same channel/pre-amp setting.
When either a Channel preset or Footswitch preset
has been altered the Digital Display (3) will begin to
flash. The footcontroller will flash the relevant number
if a Footswitch preset has been altered or will flash a
“-“ if a Channel preset has been altered.
Pressing only the Store switch at this point will
overwrite the altered Channel or Footswitch preset.
To store an altered Channel preset to the Footswitch
instead
, hold the Store switch and while held down,
press your chosen Footswitch (1) - Just like a normal
Preset Store.
To store an altered Footswitch Preset to another
Footswitch
hold the Store switch and while held
down, press your chosen Footswitch (1) - Just like a
normal Preset Store.
Digital Display
When recalling a footswitch preset, the Digital Display
(3) will indicate which footswitch number has been
pressed.
If a Channel preset has been recalled the Digital
Display (3) will remain blank.
When either a Channel preset or Footswitch preset
has been altered the Digital Display (3) will begin to
flash. The footswitch will flash the relevant number if a
Footswitch preset has been altered or will flash a “-“ if
a Channel preset has been altered.
Tuner
The Tuner can be accessed in two ways:
By simultaneously pushing the Tap (10) and Store (12)
switches on the front panel or by assigning the Tuner
to the footswitch. Note: On factory reset / first switch
on, the Tuner is already assigned to Footswitch
number 4.
Assigning the Tuner to a footswitch is carried out like
any other Switch Store. To assign the Tuner to the
footswitch hold down the Tap (10) and Store (12)
switches and press the chosen footswitch you wish to
assign it to. The Digital Display (3) will swirl to show that
the footswitch has been assigned. You can then
release the footswitch and front panel switches.
For all amplifiers, when entering Tuner mode the unit
mutes and Clean/Crunch (3) and OD-1/OD-2 (5)
switches light yellow.
The Digital Display (3) indicates the closest current
note being played. The indicator dot on the lower
right hand corner shows if the current closest note
is #.
The LED Status Panel (2) is used to show how far away
from the closest note the current note being played
is. When the central FX Status LED lights, it indicates
the correct tuning, with the others progressively
indicating the tuning is up to 50 cents up or down.
To exit the Tuner push any footswitch, the amplifier will
then exit returning to the settings before entering.
1
3
2
1. Footcontroller
Each footswitch can be assigned a different stored function.
2. LED Status Panel
This always reflects the current status of the amplifier or tuner details:
CLN & OD:
Current Channel
REV:
Reverb On/Off
FX:
FX Section On / Off
Ext FX:
External FX Loop On/Off (MG50CFX & bigger)
Damp:
Damping Mode (MG50CFX & bigger)
Tap:
Tap Tempo speed.
3. Digital Display
This display indicates the various functions of the footcontroller.
EN
G
LIS
H
Summary of Contents for MG15HCFX
Page 1: ......
