2D Fixed
Barcode Scanner
2D Fixed Barcode Scanner Quick Guide (Rev2)
P/N: 8013-0055001
SPECIFICATIONS
STEP1 - CONNECT TO HOST
STEP2 - CONFIGURE INTERFACE
STEP3 - POSITION SCANNER
STEP4 - INSTALL SOFTWARE UTILITY
DIMENSION
SCANNING RANGE
Light source
625nm visible red LED
Aimer
650nm visible red Laser
Scan rate
60 frames/sec
Resolution
5mil/ 0.127mm
PCS
30%
Width of Field 131mm (13Mil Code39)
Depth of Field 5 Mil Code39: 55 - 160mm
10 Mil Code39: 65 - 270mm
13 Mil UPC/EAN: 65 - 285mm
10 Mil DataMatrix: 50 - 125mm
10 Mil QR Code: 65 - 130mm
Dimension
W56 x L41 x H20 mm
Housing
ABS (Housing), PC (Back Cover)
Weight
120g ± 10g
Cable Length 90cm/35.4in (Fixed Cable)
Interface
RS232, USB HID, USB VCP
Voltage
5VDC±5%
Working Current
< 320mA
Standby Current
< 100mA
Operating Temp.
-10 to 55˚C (14˚F to 131˚F)
Storage Temp. -20 to 65˚C (-4˚F to 149˚F)
Ambient Light 30,000 lux
Drop Durability
1.5M
Sealing
IP55
Symbologies QR Code, DataMatrix, PDF417 and all
major 1D barcodes
Top View
Front View
RS232 (D-Sub 9 Female):
Pin
Signal
2
3
5
7
8
TXD(Out)
RXD(In)
GND
CTS(In)
RTS(Out)
USB Connection
USB Connection
RS232 Connection
RS232 Connection
1. Connect the scanner to the host.
2. The scanner will be powered by the USB connection.
1. By default, barcode data will be sent as HID keyboard
input (USB HID).
2. Below configuration barcodes allow you to switch
between two USB modes (USB HID & USB VCP)
3. For USB VCP driver, please download it from our web-
site or contact your local distributor.
4. Only USB VCP interface allows you to enable software
trigger (see back page for details)
2. Pitch the scanner at a minimum of ±5˚ to avoid specular
reflection.
1. Maximum Scan Angle: Skew ±55˚, Pitch ±55˚, Tilt ±360˚
Skew ±55˚
Pitch ±55˚
Tilt ±360˚
Based on different hardware & configuration method,
there are 2 types of software utility:
1.
EZU
Software - works with USB HID interface
2.
BEO
Software - works with RS232 & USB VCP
and supports command operation
Both are available for download from below link:
Please visit www.marson.com.tw
and enter MT6222
>
Downloads
Or simply scan below barcode by smartphone
1. Connect the scanner to the host.
2. Supply power directly to Pin 9 or plug power adapter
to the DC Jack. The scanner will be powered up.
1. By default, barcode data will be transmitted by the
communication protocols of 9600-8-N-1
2. RS232 interface allows you to enable software trigger
(see back page for details)
Quick Guide
56mm
41mm
20mm
Side View
Scanner
(Side View)
Barcode
+5VCC
9
Pin
Signal
1
2
3
+5VCC
Data -
Data +
4
GND
USB (Type A Male):
. C006$
USB VCP
. C008$
USB HID
(Top View)
5 Mi
l Code39: 55 - 1
60mm
10 Mi
l Code39: 65 - 2
70mm
13 Mi
l EAN/UP
C: 65 - 285mm
6.6
7Mi
l P
DF4
17
: 60 - 1
30mm
20Mi
l P
DF4
17
: 55 - 1
85mm
10Mi
l Dat
aMatr
ix: 50 - 1
25mm
20Mi
l Dat
aMatr
ix: 65 - 230mm
10Mi
l QR Code: 65 - 1
30mm
15Mi
l QR Code: 45 - 1
70mm
36˚
Unit: MM
Auto-sensing Area
Barcode Scanning
Area
