Marta MT-2382, User Manual

MT-2382 

7 



Always place the humidifier on a hard, flat and level surface. Avoid exposure to direct sunlight and always keep it away from walls and heat sources such as stoves, radiators, etc. Warning: The 

appliance may not work correctly if it is not placed on a level surface. 



Do not insert or remove the electric plug on the appliance with wet hands. 



If the mains cable is damaged it must be replaced by the manufacturer, its service agent, or similarly qualified persons in order to avoid a hazard. 



To reduce the risk of electric shock, do not remove screws. The unit does not contain any user-serviceable parts. Please leave all maintenance work to qualified personnel. 



Fill the tank with fresh, distilled or demineralized water. Do not switch on the appliance when there is no water in the tank. 



Do not shake the appliance as this might cause the water spill over into the base unit. 



If you spill any liquid into the unit, it can cause serious damage. Switch it off at the mains immediately. Withdraw the mains plug and consult your dealer. 



Never touch the water or components while the unit is in operation. 



If there is an unusual smell when it is being used as described in these manual, switch the appliance off, unplug it and have it examined by your dealer. 



Do not pour hot water into the tank, i.e. at a temperature in excess of 40°C. 



Unplug the appliance before cleaning it or removing the tank. 



Do not immerse the appliance or the mains cable or plug in water or other liquids. 



Never scrape the transducer with a hard tool. The humidifier must be cleaned regularly. To do this, refer to the cleaning instructions in this manual. 



If you spill any liquid into the unit, it can cause serious damage. Switch it off at the mains immediately. Withdraw the mains plug and consult your dealer. 



Disconnect the unit from the power supply when not in use and before cleaning. 



Ensure that the mains cable does not touch any hot surface and that it does not overhang a table edge. 



Never use this appliance in a room where aerosol products (sprays) are used or in a room or where oxygen is being administered. 



Do not put items of clothing or towels on top of the appliance. If the nozzle is obstructed, this may cause the appliance to malfunction. 



When moving the appliance, lift it by the base unit and not by the water tank. 



Do not use the humidifier if the air in the room is already sufficiently humid (relative humidity of at least 50%). 



The ideal relative humidity level for human comfort is in fact between 45% and 60%. Excess humidity shows up in the form of condensation on cold surfaces or cold walls in the room. To measure the 

room’s humidity correctly, use a hygrometer available in most specialist shops and hypermarkets. 



The humidifier is designed for indoor and domestic use only. 

CLEANING AND MAINTENANCE 

ATTENTION!

 Always switch off and unplug the unit before cleaning. 

You can ensure many years of trouble free operation of your humidifier by following a few simple maintenance procedures. If your water is hard, containing high concentrations of calcium and other minerals, 
then over a period of time white dust will start to deposit on the various surfaces in the room. A white, film-like substance will also start to develop in the water basin, on the transducer and on the inner surface 

of the water tank. This white film will impede the proper function of the transducer and the operation of the machine. 
Use cold boiled water or distilled water. 

Clean the transducer, water tank and basin unit every week. 
Change the water in water tank more often to keep it fresh. 
Make sure to pull out the water from the water tank and dry the water basin before you store the unit unused for a long period of time. 

Clean the whole unit and make sure that all parts of the unit are dried completely before unused for longer period of time. 
How to clean the transducer: 
Put 5-10 drops of cleaning abluent on the surface of the transducer; wait for 2-5 minutes. 

Brush off the scale from the surface. 
Rinse the transducer with clean water.