Model MTS-SBLD1
Form No. SJ-MTS-SBLD1-880E-M
OPERATOR’S MANUAL
SHARPERBLADE ELECTRIC T EDGER
12.6-INCH | 4.5-AMP | STRINGLESS
© 2017 by Snow Joe
®
, LLC
All rights reserved. Original instructions.
SAVE THESE INSTRUCTIONS
1
IMPORTANT!
Safety Instructions
All Operators Must Read These
Instructions Before Use
m
CAUTION!
Before using this electric tool, carefully read and observe the
safety rules and instructions listed below. Before starting work,
make sure that you know how to stop the machine in case of
an emergency. The incorrect use of this machine could cause
serious injury. Keep these instructions in a safe place and on
hand so that they can be consulted when required.
m
CAUTION!
The electric grass t edger should only be used for
cutting lawns and for trimming along the borders of flower
beds. Other uses of the t edger that are not indicated
in these instructions could damage the t edger or
seriously injure the operator.
GENERAL Safety Rules
m
WARNING!
When using the electric grass trimmer
+ edger basic safety precautions should always be followed
to reduce the risk of fire, electric shock, and personal injury,
including the following:
A) FOR ALL DOUBLE–INSULATED APPLIANCES
1. Replacement parts – When servicing, use only identical
replacement parts.
2. Polarized appliance connections – To reduce the risk
of electric shock, this appliance has a polarized plug (i.e.
one blade is wider than the other) and will require the use
of a polarized extension cord. The appliance plug will fit
into a polarized extension cord only one way. If the plug
does not fit fully into the extension cord, reverse the plug.
If the plug still does not fit, obtain a correct polarized
extension cord. This plug will fit into the polarized wall
outlet only one way. If the plug still does not fit fully into
the wall outlet, reverse the plug. If the plug still does not
fit, contact a qualified electrician to install a proper wall
outlet. Do not change the appliance plug, extension cord
receptacle, or extension cord plug in any way.
B) FOR ALL APPLIANCES
1. Avoid dangerous environments – Do not use appliances
in damp or wet locations. Do not use in rain.
2. Keep children and bystanders away – Children and
other spectators, including pets, should be kept at least
50 feet (15 meters) away from the work area. When the
grass is cut, stones and debris contained in the grass can
be picked up by the t edger and dispersed into
the air. These flying projectiles can cause blindness or
other bodily injury.
3. Dress properly – Always wear suitable clothing when
using the t edger to prevent head, hand, or feet
injuries. Do not wear loose clothing or jewelry. They can
get caught in moving parts.
4. Use safety glasses – Also use safety footwear,
snug-fitting clothing, protective gloves, hearing and head
protection.
5. Use the right tools – Do not use tools for any job except
that for which they are intended.
6. Avoid unintentional starting – Do not carry plugged-in
tool with finger on the trigger. Make sure the switch is off
before plugging in the tool.
7. Do not abuse the cord – Never carry the tool by the cord
or yank the cord to disconnect it from the receptacle.
Keep cord away from heat, oil, and sharp edges.
8. Do not force the tool – It will do the job better and with
less likelihood of injury if it is used at the rate for which it
was designed.
9. Do not overreach – Keep proper footing and balance at
all times.
10. Stay alert – Watch what you are doing. Use common
sense. Do not operate the t edger when you are
tired, or under the influence of alcohol or drugs.
11. Disconnect the tool – Turn the t edger off and
disconnect the plug when: the t edger is not in
use; it is left unattended; it is being examined because it is
not working correctly; the power supply cable is damaged;
the trimmer line is being removed or changed or when
the t edger is being moved from one place to
another.
12. Store idle tools indoors – When not in use, tools should
be stored indoors in a dry and high or locked-up place out
of the reach of children.
13. Maintain tools with care – Keep cutting edges sharp
and clean for best performance and to reduce the risk
of injury. Follow instructions for lubricating and changing
