background image

All material © 2009. Martin Audio Ltd. Subject to change without notice. 

 

If they are not, the message 
 

Bypass PEQ’s 6 & 7 To Access 48dB Slopes

 

 
will be displayed. 
 

   Freq       Slope 

 

 

The display will show, for instance 
 

OP1   Output 1  HPF /~~ 
<10Hz  Linkw-Riley 48dB 

 
 

Output Low Pass Filter 

The low pass crossover filter on each output has a frequency range of 35.1Hz up to >32kHz 
in 1/36

th

 Octave steps. 

 
If you try to set the low pass filter to a lower frequency than the high pass (which would be 
pointless and result in no output), the message High/Low Freq. Overlap! will be displayed.  
Note that to access the 48dB/Octave filters, parametric bands 8 & 9 need to be bypassed, or 
set to 0dB. 
 
If they are not, the message 
 

Bypass PEQ’s 8 & 9 To Access 48dB Slopes 

 
will be displayed. 
 

   Freq       Slope 

 

 

The display will show, for instance 
 

OP1   Output 1  LPF ~~\ 
>32kHz  Linkw-Riley 48dB 

 
(Note that 2 bands each will be lost when using 48dB slope crossover filters, resulting in a 
maximum of 5 bands of EQ when both high and low pass are set to 48dB/Octave) 

 
 

Output Parametric EQ 

There are nine bands of parametric equalisation available on every output. The behaviour of 
each individual band can be changed to a variety of different filter shapes, including high and 
low shelves, notch, and band-pass. 
 
Changing the filter type is achieved by pressing 

BYPASS

 to bypass the filter and then 

pressing 

ENTER

 during editing any particular band. 

 

   Freq           Q            Gain 

 

 

Summary of Contents for DX1.5
























Reviews: