background image

GENERAL SAFETY INFORMATION: Always read before proceeding.

Warning
These instructions contain both information and warnings that are  
necessary for the safe operation and maintenance of this product. It is 
recommended that you read the instructions carefully and ensure that the contents 
are fully understood. Failure to understand and to comply with the warnings and 
instructions can result in serious injury, damage or even death.

In order to avoid the danger of electrical shock, it is important that proper safety 
measures are taken when working with voltages exceeding 30V AC RMS, 42V AC 
peak or 60V DC.

This product must only be used by a competent person capable of interpreting 
the results under the conditions and for the purposes for which it has been 
constructed. Particular attention should be paid to the Warnings, Precautions and 
Technical Specifications. Always check the unit is in good working order before 
use and that there are no signs of damage to it. Do not use if damaged.

Where applicable other safety measures such as use of protective gloves, goggles 
etc. should be employed.

Please keep these instructions for future reference. Updated instructions and 
product information are available at: www.martindale-electric.co.uk
 
REMEMBER: SAFETY IS NO ACCIDENT

MEANING OF SYMBOLS: 

 

Equipment complies with relevant EU Directives

 
 

Caution - risk of danger & refer to instructions

 
 

Caution - risk of electric shock

  Equipment protected by double or reinforced insulation (Class II)

  End of life disposal of this equipment should be 
  in accordance with relevant EU Directives

 

Direct current (DC)

  Alternating current (AC)

  Earth (ground)

Summary of Contents for MM64





















Reviews: