background image

g

eneral

 I

nformatIon

14     General Information

The Dynamo 500 subwoofer system consists of a single 

woofer for high SPL output with minimal distortion. The 

equalization used is specifically designed to counteract 

the response of the woofers sealed box response. This 

equalization leads to minimal group delay and proper 

transient response.

System Frequency Response

29–200 Hz ± 3 dB. Anechoic in the LFE mode.

Low Pass Filter Frequencies

50Hz–200Hz

Low Pass Filter Switch

Bypass (LFE In), Variable (L&R In)

Phase

0°, 180°

Components

10” (25.4cm) high-excursion, polypropylene cone with 

extended throw driver assembly; ported

Amplifier

120 watts RMS (360 watts peak)

Impedance

Left & Right/LFE RCA – 20,000 Ohms

Inputs

Left & Right/LFE RCA Line Level

Mains Power Draw

Standby: 12W

Idle:

 

12W

Max: 

120W

Weight

28.5 lbs. each (12.9 kg)

Size

13 inches W x 15.27 inches D x 14.69 inches H

(33cm W x 38.8cm D x 37.3cm H)

Your Dynamo 500 subwoofer is provided with an auto-

matic Limited 90 Day Warranty coverage.

You have the option, at no additional charge, to receive 

Limited 3-Year Warranty coverage. To obtain the Limited 

3-Year Warranty coverage you need to complete and 

return the Certificate of Registration, included with your 

subwoofer, and provide a copy of your dealer receipt, to 

MartinLogan within 30 days of purchase. 

For your convenience MartinLogan also offers online warranty 

registration at www.martinlogan.com.

MartinLogan may not honor warranty service claims unless 

we have a completed Warranty Registration card on file!

If you did not receive a Certificate of Registration with your 

new Dynamo 500 subwoofer you cannot be assured of 

having received a new unit. If this is the case, please con-

tact your authorized MartinLogan dealer.

Service

Should you be using your MartinLogan product in a country 

other than the one in which it was originally purchased, 

we ask that you note the following:

1  The appointed MartinLogan distributor for any given 

country is responsible for warranty servicing only on units 

distributed by or through it in that country in accor-

dance with its applicable warranty.

2  Should a MartinLogan product require servicing in a 

country other than the one in which it was originally 

purchased, the end user may seek to have repairs per-

formed by the nearest MartinLogan distributor, subject 

to that distributor's local servicing policies, but all cost 

of repairs (parts, labor, transportation) must be born by 

the owner of the MartinLogan product.

3  If, after owning your subwoofer for six months, you relocate 

to a country other than the one in which you purchased 

your subwoofer, your warranty may be transferable. 

Contact MartinLogan for details.

Warranty and Registration

Specifications

Summary of Contents for Dynamo 500



















Reviews: