TECHNICAL SPECIFICATIONS
NOTE:
Check the product label for your unit’s specifications.
TROUBLESHOOTING
Problem
Possible Cause
Solution
AC power is
available, but the
outlets stopped
providing power to
connected
equipment.
Circuit breaker tripped due to an
overload.
Turn the UPS off and unplug at least one piece of equipment. Reset the circuit breaker by depressing the red button.
Turn the UPS on.
Low battery or battery voltage less
than 10V.
Allow the UPS to charge for at least 8 hours. The low battery may be due having recently experienced a power
disturbance that drained the battery(ies) or the battery(ies) may need to be replaced with new ones.
Control board failure.
Control board needs to be replaced. Contact or your local authorized retailer for fastest support. You can also contact
AC power voltage is beyond accepted
range.
If the UPS detects the incoming AC power to be below or above the accepted voltage range, the UPS will not power on to
protect connected equipment. Please wait a few minutes before turning on the UPS.
The UPS is always
in Battery Mode.
Power cord is loose.
Check the power input connection at the mains and input connection on the UPS to power supply cord.
Circuit breaker tripped.
Turn the UPS off. Reset the circuit breaker by depressing the red button. Turn the UPS on.
Control board failure.
Control board needs to be replaced. Contact or your local authorized retailer for fastest support. You can also contact
The battery does
not perform to the
expected runtime.
Battery is not fully charged or has
not recharge fully since last time
battery backup mode.
Allow the UPS to recharge fully by leaving the UPS plugged in.
The UPS is overloaded.
Remove at least one non-critical equipment. Keep removing equipment until the UPS is no longer overloaded.
End of battery service life.
Replace battery or contact
Battery defect.
If the battery is less than one year old, it the shorter runtime may be due to operating in high temperatures or improper
operation of the battery. Replace the battery with the same type of battery.
If replacing the battery does not resolve the issue, contact your local authorized retailer. You may also contact us at
UPS beeps
continuously.
UPS is overloaded.
Turn the UPS off and unplug at least one piece of equipment before turning the UPS back on.
LIMITED WARRANTY
The 650VA / 850VA / 1200VA / 1650VA / 2200VA Power Pro LCD (individually and collectively, the “Product”) includes limited warranties Maruson Technology Corporation
(referred to herein as “Maruson”) offers for customers who register their product within fifteen (15) days of the invoice date. These limited warranties are only for the original end-
user (“Original Purchaser”). Please retain a copy of your receipt as proof of purchase. All Warranty claims must be made within ten (10) days of occurrence. If you need to file a
claim, contact your local authorized dealer first or fill out the RMA form online from the Maruson website. Terms and conditions apply. Visit our website for details. To register your
product, go to
www.MarusonUSA.com
>
Support
>
Registration
(left column).
Maruson warrants the Original Purchaser of this Product that the product is free from defects in materials and workmanship under normal use and service for which the product
was designed for a period of three (3) years for Limited Product and two (2) years for Limited Battery Warranty. The limited warranties start date is based on the date of purchase.
If, in the opinion of Maruson, the UPS or battery is defective and defective within the scope of this warranty, Maruson’s sole obligation will be to repair or replace the defective
UPS or battery. No salesperson, employee, or agent of Maruson is authorized to add to or vary the terms of the warranties. By using the Product, you agree to the terms of the
Limited Warranty. The duration of warranty coverage does not pause, restart, or extend if the Product is with Maruson or any of its dealers for evaluation, servicing, repairs, or if a
replacement part or unit is provided.
If any payment is required as part of a service, Maruson’s obligations under this warranty are expressly conditioned upon receipt by customer of all payments due to it (including
interest charges, if any). During such time as Maruson has not received payment of any amount due to it for the Product, in accordance to the contract terms under which the
Product is sold, Maruson shall have no obligation under this warranty.
WHAT IS NOT COVERED
Maruson shall not be liable for costs, damages, or repairs incurred as a result of, due to, or from:
•
Warranty for purchase of unit from unauthorized dealers, second-hand units, or units that were transferred.
•
Improper usage, operation, handling, tampering, misuse, abuse, lack of maintenance, and/or use of the UPS or connected equipment not in accordance with the User
Manual.
•
Damage from fire, flood, wind, rain, rising water, theft, vandalism, lightning, or other acts of God, leakage or breakage of plumbing, harsh chemical action, intentional
misconduct on the part of the consumer, accident, dropping the device, abuse or other abnormal conditions, or unauthorized modifications.
•
Normal wear and tear, including normal wearing parts such as the power cord (or where external damage or abuse was diagnosed).
•
Damage from lightning or power transients. Damage from causes other than AC power line transients, spikes, or surges on properly installed, grounded and code-compliant
120Vac power lines; transient surges or spikes on standard telephone land lines, PBX telephone equipment, or base 10T ethernet lines, when properly installed
•
Economic loss or special, indirect, or consequential including without limitations; loss or damage to data, records, or software or the restoration of data or records, or the
restoration of software, whether or not on account of product failure.
•
Damage as a result of use not in accordance with the rating plate.
•
Units with the serial number altered or removed.
•
Reduction of battery discharge time due to battery age or use.
•
Packaging and shipping costs to ship from the customer to Maruson for warranty service.
DISCLAIMER OF WARRANTIES, INCLUDING WARRANTY OF MERCHANTABILITY AND WARRANTY OF FITNESS FOR PARTICULAR PURPOSE: EXCEPT AS
SPECIFICALLY SET FORTH HEREIN, NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, IS MADE AS TO THE UPS. EXCEPT AS EXPRESSLY SET
FORTH HEREIN, MARUSON AND/OR ITS AFFILIATES EXPRESSLY DISCLAIMS, WITHOUT LIMITATION, ANY STATUTORY WARRANTIES, AND ALL IMPLIED
WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL MARUSON, ITS
AFFILIATES, ASSOCIATES, DEALERS, AGENTS OR SUPPLIERS OR THEIR RESPECTIVE OFFICERS, DIRECTORS, EMPLOYEES, AND ASSIGNS BE LIABLE FOR
INCIDENTAL, SPECIAL, DIRECT, INDIRECT, EXEMPLARY, PUNITIVE, SPECIAL, CONSEQUENTIAL, OR MULTIPLE DAMAGES SUCH AS, BUT NOT LIMITED TO
BUSINESS INTERRUPTION, LOST BUSINESS OR PROFITS, PERSONAL INJURY, LOSS OF ABILITY TO USE THIRD-PARTY PRODUCTS OR SERVICES, FAILURE TO
MEET ANY DUTY INCLUDING OF GOOD FAITH OR REASONABLE CARE, NEGLIGENCE, OR LOSS OF DATA ARISING OUT OF THE SALE, USE, OR INABILITY TO USE
OF ANY MARUSON UPS, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL THE TOTAL AGGREGATE LIABILITY OF MARUSON, ITS
AFFILIATES, ASSOCIATES, DEALERS, AGENTS OR SUPPLIERS TO YOU FOR ALL DAMAGES EXCEED THE PRICE YOU PAID FOR THE PRODUCT. THIS LIMITATION
IS CUMULATIVE AND WILL NOT BE INCREASED BY THE EXISTENCE OF MORE THAN ONE INCIDENT OR CLAIM. THE FOREGOING LIMITATIONS WILL APPLY EVEN
IF ANY WARRANTY OR REMEDY PROVIDED FAILURES OF ITS ESSENTIAL PURPOSE. NOTHING IN THIS SECTION SHALL LIMIT THE LIABILITY OF MARUSON IN
RELATION TO DEATH OR BODILY INJURIES. THE PRODUCTS LISTED IN THIS WARRANTY ARE NOT FOR USE IN CONNECTION WITH ANY NUCLEAR, MEDICAL,
LIFE-SUPPORT, AND RELATED APPLICATIONS.
This warranty gives you specific legal rights, and you may also have other rights, which may vary from state to state. Some states or provinces do not allow the exclusion or
limitation of incidental or consequential damage, so the limitations stated may not apply to you. The English version of this warranty and policy will always prevail if there are
inconsistencies with a translated version.
SUPPORT
If the unit requires service or you are having difficulty using the unit, follow these steps:
1. Review the Troubleshooting section of the manual to see if that resolves the issue.
2. Contact your local authorized distributor for support. If you are not able to get ahold of your local authorized distributor, contact Maruson Technical Support at +1-800-627-8766
or
. We’re available Monday through Friday, 9 AM to 5 PM (Pacific Time). We will need your model number, serial number, and description of issue
and connected equipment for support.
a. If we are unable to resolve the issue over phone or email, the technician will issue a Return Authorization Number (RMA #) to ship the unit back for repair.
b. If the unit is under warranty, the repairs are free.
3. Pack the unit in the original packaging to avoid damage during transit. Damage sustained during transit and lost packages on the way to or from Maruson are not covered
under warranty. The customer is responsible for all shipping costs (including duties and taxes if outside US) to ship to and from Maruson.
4. The RMA number must be marked on the outer packaging and return the unit by insured, pre-paid carrier to the address provided by the technician. Packages without an RMA
number on the outside package and collect shipments will be refused.
BATTERY REPLACEMENT
Carefully read the cautions and warnings in this manual before attempting to replace the batteries; not doing so can cause serious injury, shock, or fire.
Failure to connect to
the correct terminals may cause damage to the UPS, battery(ies), or other damages.
It is normal for small sparks to be seen when the battery cable is connected the
battery terminal. Recycle spent batteries. Always use new batteries for replacement, do not use recycled batteries.
1. Turn off and unplug all connected equipment from the UPS. Turn off the UPS and unplug the unit
from the AC power source.
2. Remove the two screws under the UPS’ front panel with a Phillips screwdriver.
3. Carefully remove the front panel from the UPS by lifting the bottom of the front panel outward from
the UPS and upward.
4. Remove the plastic mount in front of the battery(ies) by sliding it up.
5.
650VA / 850VA Models:
Remove the spent battery from the UPS. Disconnect the
black
(
negative
,
-
) wire from the battery terminal, then disconnect the
red
(
positive
,
+
) wire. When replacing with a
new battery, connect the
red
(
positive
,
+
) wire to the
positive
(
+
) terminal first, then connect the
black
(
negative
,
-
) wire to the
negative
(
-
) battery terminal.
1200VA / 1650VA / 2200VA Models:
Remove the spent batteries from the UPS. Disconnect the
black
(
negative
,
-
) wire from the first battery, then remove the jumper wire from the
negative
(
-
)
terminal on the second battery. Next, remove the jumper wire from the
positive
(
+
) terminal on the
first battery, before removing the
red
(
positive
,
+
) wire from the second battery. Remove the spent
batteries from the UPS and place the new batteries into the battery compartment for wiring.
When replacing with new batteries, connect the wires in reverse. Connect the
red
(
positive
,
+
) wire
to the
positive
(
+
) terminal on the second battery, then connect one end of the jumper wire to the
positive
(
+
) terminal on the first battery. Next, connect the other end of the jumper wire to the
negative
(
-
) terminal on the second battery. Finish up by connecting the
black
(
negative
,
-
) wire to
the negative battery terminal of the first battery.
6. Replace the battery compartment cover. Plug the UPS to a wall outlet to recharge the UPS battery for
at least 6 hours before turning the UPS on for use.
© 2021 Maruson Technology Corporation. Maruson, Maruson Technology, and the Maruson logo are owned by Maruson Technology Corporation or their affiliated companies. All
other trademarks mentioned are the property of their respective owners. The information contained herein is subject to change without notice. While every precaution has been
taken to ensure accuracy and completeness herein, Maruson assumes no responsibility, and disclaims all liability, for damages resulting from use of this information or for any
errors or omissions.
Maruson Technology | PO Box 1986, Walnut, CA 91788, USA | www.MarusonUSA.com
701-0071624 UPS-Mar-Pro-NLCD-01
Model
PRO-650LCD
PRO-850LCD
PRO-1200LCD
PRO-1650LCD
PRO-2200LCD
Capacity
650VA / 390W
850VA / 510W
1200VA / 720W
1650VA / 990W
2200VA / 1320W
Nominal Voltage
110 /115 / 120Vac or 220 / 230 / 240Vac
Input Voltage Range
110 / 115 / 120Vac models: 80 – 145 Vac; or
220 / 230 / 240Vac models: 154 – 280 Vac
Frequency Range
47 – 63 Hz (auto sensing)
Output Voltage
110 /115 / 120Vac or 220 / 230 / 240Vac
Regulation Steps
2-Steps Up and 1-Step Down Automatic Voltage Regulation
On-Battery Output Wave Form
Simulated Sine Wave
On-Battery Output Voltage
110 /115 / 120Vac or 220 / 230 / /- 10%
On Battery Output Frequency
50 / 60 Hz +/- 1%
Battery Type
Sealed Maintenance-Free Lead Acid Battery
Battery Size
12V / 7.2Ah x 1
12V / 9Ah x 1
12V / 7.2Ah x 2
12V / 9Ah x 2
12V / 9Ah x 2
Battery Charging Voltage
13.7Vdc +/- 2%
27.4Vdc +/- 2%
Battery Recharge Time
Typically, < 5 hours to 90% Capacity
Transfer Time
2 – 6 ms (typical)
Full Protection
Discharge, Overcharge, and Overload Protection
EMI Filtering
Yes
Surge Protection
320 Joules
480 Joules
USB Communication Port
Yes
Phone / Fax / Network Surge
Protection
RJ-11 / 45 (1-in, 1-out)
(650VA & 850VA models with Thailand type sockets will not have this feature.)
Power Management Software
Yes, Windows® 10 / 8 / 7 / 2008 / 2003 / 2000, Server® 2012 R2 / 2008 R2, Linux®, Unix, Mac®
Auto-Charger
Yes
Auto-Restart
Yes
Operating Temperature
0°C up to 40°C / 32 up to 104 °F
Operating Relative Humidity
0 to 90% Non-Condensing
Noise Level
Less Than 40 dB
Dimensions (DWH)
315.5 x 100 x 141 mm / 12.4 x 3.9 x 5.6 in
343 x 135 x 208 mm / 13.5 x 5.3 8.23 in
Product Weight
4,7 kg / 10.4 lb
5,7 kg / 12.6 lb
8,1 kg / 17.9 lb
9,7 kg / 21.4 lb
11,4 kg / 25.1 lb
Align the arrows on the battery
compartment cover with the
UPS to remove the cover.
1200-2200VA Wires Removal:
1. Remove
black (-)
wire first.
2. Remove jumper wire on the
negative terminal of the
second battery.
3. Remove the jumper wire
from the positive terminal on
the first battery.
4. Remove
red (+)
wire.
5. Reverse the steps when
installing new batteries.
4
3
1
2
