background image

 

 

 

 

 

1.3 Warnings 

 

  The  installation  of  the  Rangitata  ULEB  requires  a  building  consent  before  installation 

commences.    Check  with  your  local  Building  Authority  whether  there  are  any  additional 
requirements before starting installation. 

  The  Rangitata  ULEB  burner  and  flue  system  shall  be  installed  in  accordance  with  AS/NZS 

2918:2001 and appropriate requirements of the relevant local building codes.   

  Glen  Dimplex  highly  recommends  NZHHA  trained  SFAIT  (Solid  Fuel  Appliance  Installation 

technician) installer for installation of Rangitata burner.  Your dealer or heating specialist will 
be able to help with recommendations as well as advice on permits/consents required for the 
installation in your area.  

  Please  read  carefully  all  the  dimensions  and  recommendations  provided  on  the  technical 

specification section of this manual.  The dimensions given comply with the required safety 
standard AS/NZS 2918:2001.  

  Safety  and  emissions  performance  of  Rangitata  ULEB  can  be  affected  by  altering  the  appliance; 

hence no modifications are allowed without written permission from the manufacturer. 

  Please  ensure  that  only  components  approved  by  Glen  Dimplex  New  Zealand  are  used  for  the 

installation, as substitutes may adversely affect performance and might nullify compliance with 
the requirements of AS/NZS 2918 safety standard. 

  The Rangitata ULEB is recommended to be installed with a Masport flue system or a flue kit 

that has been tested and comply with AS/NZS 2918:2001 Appendix F. 

  Modifying  the  dimensional  specification  of  components  may  result  in  hazardous  conditions. 

Where such action is considered, the manufacturer should be consulted in the first instance. 

  The Rangitata ULEB must be serviced at least once every 2 years from service agent trained 

and authorized by Glen Dimplex New Zealand. 

 

1.4 Caution 

 

  This  appliance  is  not  intended  for  use  by  persons  (including  children)  with  reduced 

physical, sensory, or mental capabilities, or lack of experience and knowledge unless they 
have  been  given  supervision  or  instruction  concerning  use  of  the  appliance  by  a  person 
responsible for their safety. 

  Do not leave children unattended near the alighted fire and keep them well away from the 

burner  when  in  use.  Supervise  young  children  to  ensure  that  they  do  not  play  with  the 
appliance. 

  Do  not  use  flammable  liquids  or  aerosols  to  start  or  rekindle  the  fire.    Also,  do  not  use 

such flammable materials near this appliance when it is operating. 

  Always  keep  clothing,  firewood,  furnishing,  and  other  combustible  materials  at  a  safe 

distance from the fire. 

  Do not touch any part of the fire other than the door and the damper handle when in use 

as all other components can be extremely hot.   

  Cracked/broken  door  glass,  makes  the  installation  unsafe.    Do  not  operate  the  fire  with 

cracked glass. 

  Do not attempt to clean or maintain the fire when in use or with hot embers in the firebox.   

Ensure that embers and all other parts of the burner have cooled down completely before 
starting ash removal or other maintenance.  

  Do not use the fire if there is a malfunction, a suspicion of breakage, or unusual noises.  

Contact your nearest Masport dealer or customer service team at Glen Dimplex NZ. 

  This appliance should always be operated & maintained as per instructions in this manual 

 

Failure to follow above warnings, cautionary measures 

and instruction given in this installation and operation 

manual will void the Masport warranty of this product. 

Summary of Contents for RANGITATA ULEB





































Reviews: