background image

6/17 Rev. E 57-02410 

5

CAUTION!

GROUND REQUIRED

FOR SAFE OPERATION

WARNING LABELS AND SAFETY INSTRUCTIONS 

 

 
This symbol is the safety-alert symbol.  When you see this symbol on your cabinet or in this 
manual, be alert to the potential for personal injury or damage to your equipment. 
 
 

Be sure you understand all safety messages and always follow recommended precautions and safe operating 
practices. 
 

 
NOTICE TO EMPLOYERS

  

 

You must make sure that everyone who installs, uses or services your cabinet is thoroughly familiar with all 
safety information and procedures. 

 
Important safety information is presented in this section and throughout the manual.  The following signal words are 
used in the warnings and safety messages: 
 

DANGER:

    Severe injury or death will occur if you ignore the message. 

           

WARNING:

  Severe injury or death can occur if you ignore the message. 

 

CAUTION:

   Minor injury or damage to your cabinet can occur if you ignore the message. 

 

NOTICE:

      This is important installation, operation or service information.  If you ignore the           

        

message, you may damage your cabinet. 
 

The warning and safety labels shown throughout this manual are placed on your Master-Bilt Products 
cabinet at the factory.  Follow all warning label instructions.  If any warning or safety labels become lost or 
damaged, call your customer service department at (800) 684-8988 for replacements. 
 

 

 

 
 
 
 
 
 
 
 
 

This label is located on top of the electrical control 

    

This label is attached to the cabinet power cord                               on models with a power cord. 
          label and on the wiring channel. 

 

 

 

     

 

 
 
 
 
 
 
 
 
 
 
 

 

 

Summary of Contents for IHC-27

















Reviews: