1
2
3
4
5
6
7
8
LUX
L
N
120-230V
50-60Hz
MAX 5(3)A
230V
L
N
POWER SUPPLY
FUSE
1
2
3
4
5
6
7
8
LUX
L
N
120-230V
50-60Hz
MAX 5(3)A
230V
L
N
POWER SUPPLY
Dear Customer, thank you for purchasing a MASTER S.p.A. product. This guide contains all the information you will need concerning the use of this product. Read the instructions
carefully and keep them for further consultation. The module MIR LUX is specially designed for the control of lighting devices powerwd to the mains voltage. All other use beyond the field
defined by MASTER S.p.A. is forbidden. This, as well as the breach of the instructions given in this guide, shall release MASTER S.p.A. from any liability and shall annul the product
warranty.
MIR LUX
R
433,42 MHz
rev02.2_23/06/2017
03. FIRST INSTALLATION
01. Give power to the module. The lighting device emits 4 short flashes.
02. Within 15 sec press
STOP
of transmitter you want memorize.
03. The lighting device emits 1 short flash to indicate that the operation
was successful.
END OF INSTALLATION!
04. MEMORIZATION / DELETION OF A TRANSMITTER
05. COMMAND FROM TRANSMITTER
06. COMMAND FROM BUTTON
01. If is lit, turn off the lighting device to see the blinking signals.
02. Press for approximately 5 seconds the PROG button of a transmitter already memorized.
The lighting device emits 2 short flashes
03. Within15 sec press
STOP
of transmitter you want memorize/delete.
04. The lighting devicer emits 1 short flash to indicate that the operation was successful.
UP
:
switch ON the lighting device
DOWN / STOP
:
switch OFF the lighting device
FOR ME
:
if the lighting device is OFF, it switches ON. After the working time (see section 08. WORKING TIME), if the lighting device is still lit is automatically turned OFF.
STOP + FOR ME
: activates the "presence simulator" (for details see section 09. PRESENCE SIMULATOR)
The button can operate in "
Manual power off mode
" or in "
Auto power off mode
" (see section 07. OPERATING LOGIC OF BUTTON).
“
Manual power off mode
”
: -
to turn ON the lighting device briefly press the button
- to turn OFF the lighting device briefly press the button
“
Auto power off mode
”:- to turn ON the lighting device briefly press the button; when working time is elapsed the lighting device will turn automatically OFF.
- to turn OFF the lighting device briefly press the button
- a long pressure (greater than 5 sec) turns on the lighting device; to turn it OFF you must press button again. The lighting device signals this particular condition
with a short power off.
NOTES:
The module can store up to 15 radio codes. The "out
of memory" condition is indicated by 2 flashes.
If the module has stored a single hand-held transmitter, it
can't be deleted (the non-cancellation is indicated by 2
flashes).
All products and technical specifications given in this document are subject to variation without notice. The manufacturer shall not be liable for damage resulting from improper, incorrect or unreasonable
use.
08. WORKING TIME
If you turn on the lighting device by pressing FOR ME on transmitter or by pressing the button (only if this is in «automantic power off mode»), after the working time set the lighting
device will turn off automatically. The working time is adjustable from 1 minute to 240 minutes. The factory sets the working time to 2 minutes. To modify this parameter:
ARCO
FLUTE, KUADRO, KORT
VISIO
Other transmitters..
01. If is lit, turn off the lighting device.
02. Press MENU for about 5 sec, until «rS»
appears on display
03. Press 7 times NEXT. «07» appears on
display
04. Press STOP. The lighting device signals
the current setting (1)
05. Press PREV and NEXT to set the new
setting (2)
06. Press STOP. The lighting device signals
the new setting (1)
01. If is lit, turn off the lighting device.
02. Holding down STOP, press PROG for about
1 sec, until LEDs light
03. Press 7 times DOWN.
04. Press STOP. The lighting device signals the
current setting (1)
05. Press UP and DOWN to set the new setting
(3)
06. Press STOP. The lighting device signals the
new setting (1)
01. If is lit, turn off the lighting device.
02. Press MENU, «Menu rx» appears on
display
03. Press 7 times NEXT. «07» appears on
display
04. Press STOP. The lighting device signals the
current setting (1)
05. Press UP and DOWN to set the new setting
(3)
06. Press STOP. The lighting device signals the
new setting (1)
See the User manual of
the transmitter at
section:
«RECEIVER MENU -
Function 07»
07. OPERATING LOGIC OF BUTTON
The factory sets the button in "
Manual power off mode
". To modify this parameter:
10. RESET
10.1 USING TRANSMITTER
ARCO
FLUTE, KUADRO, KORT
01. Switch off power supply to the module.
02. Connect as shown in figure.
03. Give power supply and wait 30 seconds until the lighting device emits two short flashes, to
indicate that factory conditions are restored.
04. Switch off power supply to the module.
05. Restore the connections (see section 02).
06. Reinstall the module (see section 03).
10.2 USING COMMAND BUTTON
01. If is lit, turn off the lighting device.
02. Press MENU for about 5 sec, until «rS»
appears on display
03. Press 2 time PREV / 9 times NEXT. «29»
appears on display
04. Press STOP. The display flashes, the
lighting device emits 8 flashes.
05. Press together PREV and NEXT for
about 2s until the lighting device indicates
that the reset has been performed (2
flashes).
06. Reinstall the module (see section 3).
01. If is lit, turn off the lighting device.
02. Holding down STOP, press PROG for
about 1 sec, until LEDs light
03. Press 2 time UP / 9 times DOWN.
04. Press STOP. The led flashes, the lighting
device emits 8 flashes.
05. Press together UP and DOWN for about
2s until the lighting device indicates that
the reset has been performed (2 flashes).
06. Reinstall the module (see section 3).
WARNING: This procedure restores the receiver to the default conditions (factory settings). This procedure must only be carried out by qualified technical staff. Having
carried out the reset procedure, the qualified technician must promptly carry out all the installation operations described at section 03. FIRST INSTALLATION
VISIO
Other transmitters..
01. If is lit, turn off the lighting device.
02. Press MENU, «Menu rx» appears on
display
03. Press 2 time PREV / 9 times NEXT. «29»
appears on display
04. Press STOP. The display flashes, the
lighting device emits 8 flashes.
05. Press together PREV and NEXT for
about 2s until the lighting device indicates
that the reset has been performed (2
flashes).
06. Reinstall the module (see section 3).
See the User manual of
the transmitter at
section:
«RECEIVER MENU -
Function 29»
4x
1x
ARCO
FLUTE, KUADRO, KORT
VISIO
Other transmitters..
01. If is lit, turn off the lighting device.
02. Press MENU for about 5 sec, until «rS»
appears on display
03. Press 1 time PREV / 8 times NEXT. «18»
appears on display
04. Press STOP. The lighting device signals
the current setting (1)
05.
PREV
to select «
Manual power off
»
NEXT
to select «
Auto power off
»
06. Press STOP. The lighting device signals
the new setting (1)
01. If is lit, turn off the lighting device.
02. Holding down STOP, press PROG for about
1 sec, until LEDs light
03. Press 1 time UP / 8 times DOWN.
04. Press STOP. The lighting device signals the
current setting (1)
05.
DOWN
to select «
Manual power off
»
UP
to select «
Auto power off
»
06. Press STOP. The lighting device signals the
new setting (1)
01. If is lit, turn off the lighting device.
02. Press MENU, «Menu rx» appears on
display
03. Press 1 time PREV / 8 times NEXT. «18»
appears on display
04. Press STOP. The lighting device signals the
current setting (1)
05.
DOWN
to select «
Manual power off
»
UP
to select «
Auto power off
»
06. Press STOP. The lighting device signals the
new setting (1)
See the User manual of
the transmitter at
section:
«RECEIVER MENU -
Function 18»
1x
2x
Auto power off
Manual power off
(1)
(1)
Example: if working time is
5 minutes =
5x
If working time is
72 minutes
=
7x
2x
pause
(2) Example: 15 sec = press PREV 1 time and NEXT 5 times
●
Example: 210 sec = press PREV 21 times
(3) Example: 15 sec = press UP 1 time and DOWN 5 times
●
Example: 210 sec = press UP 21 times
If working time is
10 minutes =
1x
1x
pause
LONG
NOTE:
If you try to set a working time greater than 240 min, the value is rejected and the LIGHT emits two short flashes.
To activate the function:
09. PRESENCE SIMULATOR
This function can be useful when you intend to simulate the presence of an individual inside a building. Once activated, this function turns on the lighting device for a time varying from 1
to 3 minutes, for 3 times; each activation will occur at a distance from 1 to 3 hours from each other. At the end of the three activations the function is automatically deactivated.
ARCO, VISIO
FLUTE, KUADRO, KORT
Other transmitters..
Holding down STOP also press FOR ME, until
the lighting device will flash briefly.
Press STOP 6 times and then press Down (for
5 seconds), until the lighting device will flash
briefly.
See the User manual of the transmitter at
section:
«Functions associated with transmitter buttons»
To deactivate the function:
press any button on the transmitter, or press the button connected to terminals 3 and 4 of the device. If the buttons are not pressed, the device disables the
function automatically at the end of the three activations
At the end of the product life cycle, dispose of the device in
compliance with local regulations. This product could
contain substances that are harmful to human health and
the environment: do not dispose of the product in domestic
waste.
Disposal
Do not use radio systems in places with strong interference (for example, near police stations, airports, banks, hospitals). It is in any
case advisable to carry out a technical inspection prior to installing any radio system in order to identify possible sources of
interference. Radio systems can be used where any disturbances or malfunction of the transmitter or receiver do not constitute a risk
factor, or if such factor is eliminated using appropriate safety systems. The presence of radio devices working at the same
transmission frequency (433.42 MHz) may interfere with the radio receiver and reduce the range of the system, limiting functionality.
Notes on radio systems
Power supply:
120 o 230 Vac, 50/60 Hz
Contact capacity:
5A @ 250 Vac
Dimension:
45 x 38 x 25 mm
Weight:
40 gr
Working temperature:
–20°C / +55°C
Working time:
from 1 to 240 min in «auto
power off mode»
Frequency:
433.42 Mhz
IP protection:
IP20
Memorizable radio code:
15
Range (estimated):
100m outdoor, 20m indoor
Technical specifications
01. WARNINGS
Keep these instructions for future maintenance work and disposal of the product
●
All the product installation, connection, programming and maintenance operations must be carried out
only by a qualified and skilled technician, who must comply with laws, provisions, local regulations and the instructions given on this manual
●
The electrical wiring must comply with
current IEC standards
●
Some applications require «hold-to-run» operations and can exclude the use of radio controls or require particular safety devices
01.1 Warnings for safety
Check that the package is intact and has not suffered damages in transit
●
A heavy knock and the use of unsuitable tools can cause damage
●
Do not pierce or tamper with the box in any
way. Do not modify or replace parts without the manufacturer’s permission
●
The product is designed to be inserted inside of junction boxes. The module does not provide any protection
against water and only essential protection for contact with solids
●
It is forbidden to install the module in areas not adequately protected, and near sources of heat
●
The antenna cable
carries line voltage. Do not cut the antenna cable as this would be dangerous. If the antenna cable is damaged, replace the product
●
If there are several radio appliances in the same
system, they must not be less than 1,5 m apart
●
Do not install the product near metal surfaces
The product is not intended for use of persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they are supervised
or given instructions on how to use the product by a person responsible for their safety
●
Do not allow children to play with the appliance or with the fixed control devices. Furthermore, keep
the portable control devices (remote controls) out of reach of children
01.2 Warnings for installation
01.3 Warnings for use
Make connections with power supply disconnected
●
The supply line must be equipped with a circuit breaker. The installer must fit an isolation device (with 3,5 mm minimum opening on
the contacts) upstream of the system
●
The product doesn’t provide any protection against overloads or short circuits. You must provide, on the supply line, an adequate protection to the
load, for example a fuse
●
The section of the connecting cables must be proportionate to their length and to the absorption of the load, and in any case not less than 1,5 mm
●
Use
momentary (hold-to-run) control buttons.
Do NOT use stay-put switches
●
Command buttons are connected to the main voltage, so they must be properly insulated and protected
02. ELECTRICAL CONNECTIONS
The module can be powered at 120 Vac or 230 Vac. The supply voltage must be
applied to terminals
1
and
2.
02.1 Power supply
The lighting device must be connected to terminals
6
and
7
.
02.2 Connecting the lighting device
The button must be connected to terminals
4
and
5
. You must use momentary (hold-
to-run) command button, do not use button with maintained position. More
command buttons can be connected via a parallel connection.
02.3 Connecting the command buttons (optional)
