11
Tool Specifications
Operating Controls
1
Saw blade
2
Guide shoe
3
Quick-change saw blade holder
4
On/Off switch with speed control function
5
Gear selector/lock-off
6
Battery
7
Clamping lever for guide bracket
8
Battery unlocking button
9
Charge-control indicator
10
Button
Not all of the accessories illustrated or described are included
as standard delivery.
Use as Intended
This sabre saw cuts wood, plastic, and metal. It cuts
curves and can cut flush to a surface.
For damage caused by usage other then intended,
the user is responsible.
Before Putting into Operation
The batteries are partially charged and delivered in
idle state. The battery must be activated before using
for the first time. For this, place the battery onto the
charger for a short time. The LED
9
on the battery
indicates the charge condition.
When the battery is not used for longer periods, it
switches to the idle state. In order to use the battery
again, it must be reactivated.
When the battery is completely discharged, it
switches off automatically (deep discharging not
possible). When the power tool is switched on none-
theless, the battery delivers only brief current pulses.
The power tool “flickers” as an indication that the
battery must be charged.
As a general rule:
Should the power tool not be
operative after inserting the battery, place the bat-
tery onto the charger. The indicators on the battery
and the charger then provide information about the
battery condition (see main figure).
At low temperatures, further operation is possible
with reduced power output. The battery switches off
automatically below -10 °C.
Battery Charging
A battery that is new or has not been used for a longer
period does not develop its full capacity until after
approximately 2 – 3 charging/discharging cycles.
To remove the battery
6
, press the unlocking but-
tons
8
and pull out the battery toward the rear.
Do
not exert any force.
Please refer to the enclosed “Battery Charger”
instructions for the operation of the battery charger
as well as for a description of the charging process.
The battery is equipped with an NTC temperature
control which allows charging only within a temper-
ature range of between -10 °C and +66 °C. A long
battery service life is achieved in this manner.
A significantly reduced working period after charg-
ing indicates that the batteries are used and must be
replaced.
❏
Observe the notes on environmental protection.
Charge-control Indicator
(see main figure)
The battery
6
is fitted with a charge-control indica-
tor
9
.
By pressing the button
10
, the battery charge can
also be checked when the battery has been
removed, or when the machine is at a standstill
(machine must be switched off for at least 1 minute).
After approx. 4 seconds the battery charge display
automatically turns off.
When the first display element begins to flash (0 –
10 %) the battery is almost empty and must be
recharged.
Cordless Sabre Saw
SBS 28-A
Article number
0700 207 X
Rated voltage
28 V
Stroke rate at no load
1. gear
2. gear
0 – 2000 min
–1
0 – 3000 min
–1
Stroke
28.6 mm
Weight with battery, approx. 4.1 kg
Akku
Li-Ion
Article number
0700 956 730
Temperature control
NTC
Rated voltage
28 V
Capacity
3.0 Ah
Weight, approx.
1.0 kg
SBS 28 A.book Seite 11 Montag, 3. Dezember 2007 9:49 09
Summary of Contents for SBS 28-A
