background image

W

ARRANTY

31

AIR

-

POWERED GRAVITY

-

FEED SPRAY GUN KIT 058

-

9311

-0

g. This warranty will not apply to any product or part thereof if any part from another 

manufacturer is installed therein or any repairs or alterations have been made or attempted by 
unauthorized persons.

h. This warranty will not apply to normal deterioration of the exterior finish, such as, but not 

limited to, scratches, dents, paint chips, or to any corrosion or discoloring by heat, or 
abrasives and chemical cleaners.

i.

This warranty will not apply to component parts sold by and identified as the product of 
another company, which shall be covered under the product manufacturer’s warranty, if any.

Additional limitations

This warranty applies only to the original purchaser and may not be transferred. Neither the retailer 
nor the manufacturer shall be liable for any other expense, loss or damage, including, without 
limitation, any indirect, incidental, consequential, or exemplary damages arising in connection with 
the sale, use, or inability to use this product.

Notice to consumer

This warranty gives you specific legal rights, and you may have other rights, which may vary from 
province to province. The provisions contained in this warranty are not intended to limit, modify, take 
away from, disclaim, or exclude any statutory warranties set forth in any applicable provincial or 
federal legislation.

Summary of Contents for Air-Powered Gravity-Feed

































Reviews: