background image

SAFETY GUIDELINES

7

AIR

-

POWERED GRAVITY

-

FEED SPRAY GUN KIT 058

-

9311

-0

WARNING!

Potential hazard that could result in serious injury or loss of life.

Do not allow unskilled or untrained individuals to operate the Air

-powered

 

Gravity

-

feed Spray Gun.

Use components recommended by manufacturers. Never modify the tool for 
other applications. Use only parts, nozzles, and accessories with 
specifications as mentioned in this manual 

(see section “Technical 

specifications”)

.

Inspect the tool components and attachments before operation and ensure 
that they are assembled properly and are not damaged. Failure to comply 
could result in serious injury or loss of life.

Locate the compressor in a well

-

ventilated area for cooling, a minimum of 

12

"

 (31 cm) away from the nearest wall.

Protect the air hose and the power cord from damage and puncture. Inspect 
them for weak or worn parts every week, and replace them if necessary.

Always wear hearing protection when using the air compressor. Failure to do 
so may result in hearing loss.

Do not carry the compressor while it is running.

Do not operate the compressor if it is not in a stable position.

Do not operate the compressor on a rooftop or in elevated position that 
could allow the unit to fall or be tipped over.

Always replace a damaged gauge before operating the unit again.

Summary of Contents for Air-Powered Gravity-Feed

































Reviews: