background image

Warranty

Section 6  

Warranty, Product Return and 

Technical Assistance 

Use only MASTERFLEX precision tubing with MASTERFLEX pumps 
to ensure optimum performance. Use of other tubing may void applicable 
warranties. 

This product is warranted against defects in material or workmanship, and 
at the option of the manufacturer or distributor, any defective product will 
be repaired or replaced at no charge, or the purchase price will be refunded 
to the purchaser, provided that: (a) the warranty claim is made in writing 
within the period of time specified on the warranty card, (b) proof of 
purchase by bill of sale or receipted invoice is submitted concurrently with 
the claim and shows that the product is within the applicable warranty 
period, and (c) the purchaser complies with procedures for returns set forth 
in the general terms and conditions contained in the manufacturer’s or 
distributor’s most recent catalog. 

This warranty shall not apply to: (a) defects or damage resulting from: 
(i) misuse of the product, (ii) use of the product in other than its normal 
and customary manner, (iii) accident or neglect, (iv) improper testing, 
operation, maintenance, service, repair, installation, or storage, (v) 
unauthorized alteration or modification, or (b) post-expiration dated 
materials. 

THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE 
PURCHASER, AND THE MANUFACTURER AND DISTRIBUTOR 
DISCLAIM ALL OTHER WARRANTIES, WHETHER EXPRESS, 
IMPLIED, OR STATUTORY, INCLUDING WITHOUT 
LIMITATION, WARRANTIES OF MERCHANTABILITY AND 
FITNESS FOR A PARTICULAR PURPOSE. NO EMPLOYEE, 
AGENT, OR REPRESENTATIVE OF THE MANUFACTURER 
OR DISTRIBUTOR IS AUTHORIZED TO BIND THE 
MANUFACTURER OR DISTRIBUTOR TO ANY OTHER 
WARRANTY. IN NO EVENT SHALL THE MANUFACTURER 
OR DISTRIBUTOR BE LIABLE FOR INCIDENTAL, INDIRECT, 
SPECIAL OR CONSEQUENTIAL DAMAGES. 

The warranty period for this product is two (2) years from date of purchase.

Masterflex

MASTERFLEX 

®  

Gear Pump Drive Operating Manual

6-1

Summary of Contents for 75211-12



























Reviews: