background image

Page 4

SAFETY

SAFETY

Always follow safety precautions when installing and operating this jack. Keep all decals on the 
unit clean and visible. Before proceeding ensure that you fully understand and comprehend the full 
contents of this manual. Failure to operate this equipment as directed may cause injury or death. 
The distributor is not responsible for any damages or injury caused by improper use or neglect.

SAFETY MARKINGS

1. Study, understand, and follow all instructions before operating this device.
2. Do not exceed rated capacity.
3. Use only on hard, level surfaces, with less than 3 degrees of slope.
4. Lifting device only. Immediately after lifting, support the vehicle with appropriate means.
5. Do not move or dolly the vehicle while on the jack.
6. Lift only on areas of the vehicle as specified by the vehicle manufacturer.
7. No alterations shall be made to this product.
8. Only attachments and/or adapters supplied by the manufacturer shall be used.
9. Do not get under or allow anyone under the vehicle until it has been supported by jack stands.
10. Center load on saddle prior to lifting.
11. Use wheel chocks or other blocking device on opposing wheels before using jack.
12. Never use on a lawn mower or lawn tractor.
13. Do not use this jack for any use other than the manufacturer specified usage.
14. Do not rock the vehicle while working on or around equipment.
15. The following are not recommended for supporting on this equipment: Foundations, Homes, 
Mobile Homes, Trailers, RV’s, Campers, nor Fifth Wheels, etc...
16. Failure to heed these markings may result in personal injury and/or property damage.

WARNING:

                                 
Always use Jack Stands!

DO NOT USE

 wood blocks or any other non-approved load sustaining devices. The manufacturer 

only warrants loads to be sustained by jack stands that meet current ASME standards.

DO NOT USE

 wood blocks or any other non-approved lifting devices for a means of lifting with 

the jack and/or load being raised. Failure to head these warnings may cause injury or death.

WARNING:

THIS IS A LIFTING DEVICE ONLY!

•  This jack is designed only for lifting part of the total vehicle.
•  Do not move or dolly the vehicle while on the jack.
•  The vehicle must be supported after lifting immediately by 

   appropriately rated jack stands.

•  NEVER go under a vehicle that is not supported with 

   appropriately rated  jacks stands.

•  Use wheel chocks or other blocking device on opposing wheels 

   before using jack stands.

Summary of Contents for 2602007

















Reviews: