background image

JS3TA, JS6TA, JS12TA 

01/30/20

 JS3TA, JS6TA, JS12TA 3, 6, and 12 Ton Jack Stands (Pair)

IMPORTANT: READ THESE INSTRUCTIONS BEFORE OPERATING

BEFORE USING THESE STANDS, READ THIS MANUAL COMPLETELY AND THOROUGHLY, UNDERSTAND ITS OPERATING 
PROCEDURES, SAFETY WARNINGS AND MAINTENANCE REQUIREMENTS.

It is the responsibility of the owner to make sure all personnel read this manual prior to using these stands. It is also the responsibility of 
the stand owner to keep this manual intact and in a convenient location for all to see and read. If the manual or product labels are lost 
or not legible, contact Matco Tools for replacements. If the operator is not fluent in English, the product and safety instructions shall be 
read to and discussed with the operator in the operator's native language by the purchaser/owner or his designee, making sure that the 
operator comprehends its contents.

THE NATURE OF HAZARDOUS SITUATIONS

The use of portable automotive lifting devices are subject to certain hazards that cannot be prevented by mechanical means, but only 
by the exercise of intelligence, care, and common sense. It is therefore essential to have owners and personnel involved in the use and 
operation of the equipment who are careful, competent, trained, and qualified in the safe operation of the equipment and its proper use. 
Examples of hazards are dropping, tipping or slipping of loads caused primarily by improperly securing loads, overloading, off-centered 
loads, use on other than hard level surfaces, and using equipment for a purpose for which it was not designed.

METHODS TO AVOID HAZARDOUS SITUATIONS

• Read, study, understand and follow all instructions before operating this device.
•  Inspect the jack stands before each use. Do not use if damaged, altered, modified, in poor condition or unstable due to loose 
or missing components. Make corrections before using.
•  Do not use or modify this product for any other purpose than that for which it was designed without consulting the 
manufacturer's authorized representative.
•  User and bystanders must wear eye protection that meets ANSI Z87.1 and OSHA standards.
•  Use as a matched pair only.
•  Do not use beyond rated capacity. Do not shock load.
•  Maximum load capacity per matched pair shall not exceed the rated capacity of the individual stand.
•  Use only on a hard level surface capable of supporting the load.
•  Stands are to be used in matched pairs to support one end of a vehicle only. Do not simultaneously support both ends or 
one side of a vehicle.
•  Apply the emergency brake, put the gear shift lever in park or in gear if a manual shift transmission, and chock the tires that 
will not be lifted off the ground.
•  Center load on saddle. Do not use saddle lugs to support the load.
•  Check the stands for solid contact with the ground and vehicle.
•  Make sure the stand's locking pawls are fully engaging the support column's teeth.
•  Ensure both stands are set at same height and locking pawls are fully engaging the support column's teeth.
• 

Do not crawl under vehicle when placing/removing stands.

•  Consult the vehicle manufacturer for the proper frame support locations.
•  No alterations shall be made to these stands.
•  Failure to heed these warnings may result in serious or fatal personal injury and/or property damage.

CONSEQUENCES OF NOT AVOIDING HAZARDOUS SITUATIONS

Failure to read this manual completely and thoroughly, failure to understand its OPERATING INSTRUCTIONS, SAFETY WARNINGS, 
MAINTENANCE INSTRUCTIONS and comply with them, and failure to comply with the METHODS TO AVOID HAZARDOUS SITUATIONS 
could cause accidents resulting in serious or fatal personal injury and/or property damage.

This is the safety alert symbol. It is used to alert you to 
potential personal injury hazards. Obey all safety messages 
that follow this symbol to avoid possible injury or death.

WARNING:

 Indicates a hazardous situation 

which, if not avoided, could result in death 
or serious injury.

WARNING

WARNING

WARNING

WARNING

WARNING: 

This product can expose you to chemicals including nickel, which is known to the State of California to cause cancer 

and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

WARNING

Summary of Contents for JS12TA













Reviews: