background image

Some dust created by power sanding, sawing, grinding, drilling, and other 

construction activities contains chemicals known to cause cancer, birth defects or 

other reproductive harm. Some examples of these chemicals are:
  •  lead from lead-based paints,
  •  crystalline silica from bricks and cement and other masonry products, and
  •  arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type 

of work. To reduce your exposure to these chemicals: work in a well ventilated 

area, and work with approved safety equipment, such as those dust masks that are 

specially designed to filter out microscopic particles.

 MT1630
Max. Free Speed .................................................................... 2,000 RPM
Pad Size ..................................................................................................3"
Spindle Thread  Size ................................................................ 5/16" - 24T
Air Inlet ......................................................................................  1/4" NPT
Min. Air Hose Size ........................................................................ 3/8" ID
Average Air Consumption ......................................................... 2.9 CFM
Recommended Air Pressure ....................................................... 90 psig
Sound Level ..................................................................................86 dBA
Length ............................................................................................... 4.77"
Net Weight ....................................................................................  1.7 lbs.

S P E C I F I C A T I O N S

• Operating Instructions 
• Warning Information 
• Parts Breakdown

Copyright © Professional Tool Products, 2015

All rights reserved

MT1630

WARNING

WARNING

RATED RPM OF THE 

ACCESSORY USED MUST 

EXCEED THE MAXIMUM 

TOOL RPM SHOWN

ALWAYS READ 

INSTRUCTIONS BEFORE 

USING POWER TOOLS

ALWAYS WEAR 

SAFETY GOGGLES

ALWAYS WEAR HEARING 

PROTECTION

ALWAYS WEAR

BREATHING APPARATUS

AVOID PROLONGED 

EXPOSURE TO 

VIBRATION

EQUIPO DE MINI PULIDORA COMPUESTA 3

"

MINI POLISSEUSE EN COMPOSITE DE 3

"

    MINI COMPOSITE

POLISHER

3

"

RPM

RPM

RPM

Summary of Contents for MT1630














Reviews: