background image

Page 1

PRODUCT INFORMATION:

INTENDED USE OF THE TOOL

WARNING

DO NOT DISCARD – GIVE TO USER

The manufacturer warrants this product to the original 

user against defective material or workmanship for a 

period of 1 year from the date of purchase.
The manufacturer reserves the right to determine 

whether the part or parts failed because of defective 

material, workmanship or other causes. Failures caused 

by accident, alteration, or misuse are not covered by 

this warranty.
The manufacturer, at its discretion, will repair or replace

product covered under this warranty, free of charge. 

Repairs or replacements of products covered under this 

warranty are warranted for the remainder of the original 

warranty period.
The manufacturer or its authorized service representatives 

must perform all warranty repairs. Any repair to the 

product by unauthorized service representatives voids 

this warranty. The rights under this warranty are limited 

to the original user and may not be transferred to 

subsequent owners.
The warranty is in lieu of all other warranties, expressed 

or implied, including warranties of merchantability and 

fitness for a particular purpose. Some states do not allow 

the exclusion or limitations of incidental or consequential

damages, so the above limitations may not apply to you.

1 YEAR LIMITED WARRANTY

(TORCH. ACCESSORIES ARE CONSUMABLE.)

2011254-14

INDEXING PENCIL & RIGHT

ANGLE BUTANE SOLDERING KIT

 SK12PR

When unpacking, check the parts diagram and part 

number listing on page 4 to make sure all parts are 

included. If any parts are missing or damaged, please 

call your distributor. 

BEFORE USE

Study, understand and follow all instructions provided 

with this product. Read these instructions carefully 

before installing, operating, servicing or repairing this 

tool. Keep these instructions in a safe, accessible place. 

The SK12PR is designed to heat, solder and heat shrink 

electrical wiring in pencil or right-angle pistol and base 

magnet use. Do not use this tool outside of the designed 

intent. Never modify the tool for any other purpose or 

use.

Made in Taiwan

to Matco specifications

Caution: To help prevent personal injury

• Use of this product can expose you to chemicals 

including ethylene glycol, gasoline vapors and engine 

exhaust, which are known to the State of California to 

cause cancer, birth defects, or reproductive harm. For 

more information, visit www.P65Warnings.ca.gov. 

Always wear ANSI approved safety equipment, safety 

glasses and clothing when using this product. Study, 

understand, and follow all instructions provided with 

this product. Failure to read and follow all warnings 

and operating instructions may result in damages and 

serious injury or death.

• Always wear ANSI approved goggles when using this 

product. (Users and bystanders).

• Never use this tool for any application other than for 

which it was designed. 

• Only use accessories designed for this tool. 
• Never alter or modify this tool in any way. 
• Improper operation and/or maintenance of the tool, 

modification of the tool, or use of the tool with 

accessories not designed for it could result in serious 

injury or death. 

• Always select the correct accessories of the correct 

size and design for the job that you are attempting to 

perform.  

• Always work in a clean, safe, well-lit, organized and 

adequately equipped area. 

• Do not begin repairs without assurance that vehicle is 

in a secure position, and will not move during repair. 

WARNING

Dual use. 

A right-angle and pencil style torch all

in one with simple push button indexing that adjusts
from 90° to 45° to 5° for access and convenience.

Comprehensive. 

12 piece set includes torch, cap, 

cleaning tray, magnetic base, and a large 
assortment of attachments and tips.

Performance. 

Up to 1100° tip temperature and

magnetic base for pistol torch use that works on
curved and imperfect surfaces.

Summary of Contents for SK12PR













Reviews: