background image

 

Safety 

 

 

Page 5 of  14 

 

 

Safety 

Guidelines and instructions with which you must comply, are summarized in this section. 

3.1 

Intended use 

The implement must only be used in accordance with its specifications. Please read 

chapter5.1 Intended use

 all the way through. All other uses are excluded. 

Non-intended use causes: 

  Health hazards for the operator or for third parties 

  Implement damage 

  Environmental damage 

3.2 

Instructions for the owner 

3.2.1 

Instruction 

At transfer of the machine the owner of the machine receives instruction in the operation and 
maintenance of the machine from the owner's sales partner. 

The owner must ensure that operating and maintenance personnel have been instructed in full 
scope in the operation and maintenance of the machine. 

3.2.2 

Qualifications of personnel 

This machine must only be operated by persons who are qualified, as follows: 

  They must be at least 18 years old. 

  They have received instruction on the machine. 

  They must have read and understood this operating manual. 

  They have been instructed concerning the relevant safety regulations (accident 

prevention). 

The relevant accident prevention regulations and the other generally acknowledged 
occupational health and safety and road traffic regulations must be complied with at all times. 

3.2.3 

Accident prevention 

The safety regulations and accident prevention regulations are legally regulated in every 
country. The owner of the machine is responsible for compliance with the valid regulations. 

3.3 

General safety notices 

In this section general safety notices are explained that are used in the subsequent sections. 

Comply with these safety notices to ensure safe operation and to save work time and costs. 

Summary of Contents for SCA-130















Reviews: